Search found 22 matches
- Sat Sep 17, 2016 9:30 am
- Forum: Holden ALDL ECUs
- Topic: Can I isolate test distributor and ignition module?
- Replies: 3
- Views: 2506
Re: Can I isolate test distributor and ignition module?
You will still get spark even if you disconnect the PCM. The module is switched to bypass by the PCM when certain RPM reached. I would check that you have a 12v supply to the coil & to the module which should be fused.
- Sat Jul 30, 2016 5:55 pm
- Forum: Holden ALDL ECUs
- Topic: Vt hsv conversion won't run
- Replies: 53
- Views: 22072
Re: Vt hsv conversion won't run
Thanks to everyone who helped me out with my issues. Turned out to be the memcals. Put a good one in & purrs like a kitten. I still learnt plenty so that's good for the future.
- Sat Jul 16, 2016 9:27 pm
- Forum: Holden ALDL ECUs
- Topic: Vt hsv conversion won't run
- Replies: 53
- Views: 22072
Re: Vt hsv conversion won't run
Burn a new memcal using the enhanced bin. Then you can use a quality XDF and ADX. sounds like bad memcal if it changes like that can you get a read with the flash tool and post it up. a copy of the flash too can be found here http://pcmhacking.net/forums/viewtopic.php?f=3&t=82 Unfortunately bot...
- Sat Jul 16, 2016 3:13 pm
- Forum: Holden ALDL ECUs
- Topic: Vt hsv conversion won't run
- Replies: 53
- Views: 22072
Re: Vt hsv conversion won't run
I'm not sure if they are the same but thanks. The memcal is the only thing that's been changed & the second memcal is one the guy did who removed vats from my original.
- Sat Jul 16, 2016 2:27 pm
- Forum: Holden ALDL ECUs
- Topic: Vt hsv conversion won't run
- Replies: 53
- Views: 22072
Re: Vt hsv conversion won't run
I have just tried another memcal I have. So on the original memcal I get no data in the "run time" or "desired rpm" or "air/fuel ratio" fields however when I put the second memcal in it reads all of those but doesn't fire or run. I'm starting to think the PCM or MEMCAL ...
- Sat Jul 16, 2016 1:46 pm
- Forum: Holden ALDL ECUs
- Topic: Vt hsv conversion won't run
- Replies: 53
- Views: 22072
Re: Vt hsv conversion won't run
Hello. Ok I,'m still having issues with my conversion. I took some logs which showed the voltage dropping to the pcm & injector monitor. So I decided to wire it directly to the battery (fused of course) when I tried to start it it runs but cuts in & out & the data connection flashes betw...
- Sun Jul 10, 2016 3:47 pm
- Forum: Holden ALDL ECUs
- Topic: Vt hsv conversion won't run
- Replies: 53
- Views: 22072
Re: Vt hsv conversion won't run
Thanks everyone for your help, I'm an idiot!
I have managed to take a couple of logs.
It has no injector pulse time & a green FAIL beside the vats flag?
Also how do I get a list of fault codes?
I have managed to take a couple of logs.
It has no injector pulse time & a green FAIL beside the vats flag?
Also how do I get a list of fault codes?
- Sun Jul 10, 2016 12:27 pm
- Forum: Holden ALDL ECUs
- Topic: Vt hsv conversion won't run
- Replies: 53
- Views: 22072
Re: Vt hsv conversion won't run
Ok I'm lost. I have downloaded the file from "holden xdf" which I save to my downloads. I then go into tuner pro select "acquisition" then "load definition file" which takes me to my downloads folder which at that point tells me it's empty so I select all files which al...
- Sun Jul 10, 2016 9:30 am
- Forum: Holden ALDL ECUs
- Topic: Vt hsv conversion won't run
- Replies: 53
- Views: 22072
Re: Vt hsv conversion won't run
Tried the enhanced version but still gets "ADX load failure" box with failure to load box.
- Sun Jul 10, 2016 2:05 am
- Forum: Holden ALDL ECUs
- Topic: Vt hsv conversion won't run
- Replies: 53
- Views: 22072
Re: Vt hsv conversion won't run
Thanks. It will be something I'm doing or not doing.
VT V8 V1.3 $A6E.xdf(170.27 KiB) Downloaded 454 times
VT V8 V1.3 $A6E.xdf(170.27 KiB) Downloaded 454 times