Flex output ?
Flex output ?
Ok so my stupid question of the day is how do I get the flex out puts operating on an 808 ? I'm wanting to get my reverse lockout on my t-56 working and a shift light. Also what are other people using them for as i will still have 2 spare so anything that can give more hp or make driving easier or more enjoyable would be good, cheers
Re: Flex output ?
you use the flash tool to set up the axis of the flex table, then tunerpro to set the calibration of it.
see page 5 of the advanced tuning guide.
http://pcmhacking.net/forums/viewtopic.php?f=28&t=3051
see page 5 of the advanced tuning guide.
http://pcmhacking.net/forums/viewtopic.php?f=28&t=3051
Re: Flex output ?
Thanks Jayme
- Holden202T
- Posts: 10311
- Joined: Sat Feb 28, 2009 9:05 pm
- Location: Tenambit, NSW
- Contact:
Re: Flex output ?
in my Gemini i have the flex table set to run a second fuel pump on boost only, and in the past i have used one to control an electric water pump (with VL400's kit to drive it) and in my brothers car we are using flex table to activate nitrous above 3000rpm and over 99% throttle, and we are currently changing the setup to have two nos kits so we can have multi stage activation which will be all done with flex tables!
No matter what the question is, the answer is always more horsepower!
Just starting out? Have a read of the getting started guide
Basic tuning of a delco ECM with $12P thread
Advanced tuning of a delco ECM with $12P thread
Just starting out? Have a read of the getting started guide
Basic tuning of a delco ECM with $12P thread
Advanced tuning of a delco ECM with $12P thread
- TdracerTd
- Posts: 488
- Joined: Mon Aug 19, 2013 10:39 pm
- cars: Td Gemini coupe (race car WIP)
Holden VE SS ute (tow car/daily)
Vp commodore V6 (race car, s/c, e85, intercooled)
Jeep Grand Cherokee Overland (mrs car, family bus)
My12 subaru STi (Weekend warrior/Toy)
1972 LJ torana GTR (my Dad's car)
Mitsubishi Evo IX
Re: Flex output ?
I was wondering about this the other night. I have another blower which has a motorised bypass valve. I was wondering if i might be able to drive this with a flex output. It appears to be a stepper motor. I was thinking that the table to control it should be linked to the map input and TPS and have an adjustable ramp from vacuum to boost, so as the throttle opens it can close, but also remain partially closed under part throttle.
What do you guys think?
What do you guys think?
Re: Flex output ?
Not sure how the Delco would handle the current?
Re: Flex output ?
the delco cant handle much current, you need to run a driver board when using the flex output in PWM mode.
Re: Flex output ?
Hope you have a spare one to change your underpants as well !Holden202T wrote:in my Gemini i have the flex table set to run a second fuel pump on boost only, and in the past i have used one to control an electric water pump (with VL400's kit to drive it) and in my brothers car we are using flex table to activate nitrous above 3000rpm and over 99% throttle, and we are currently changing the setup to have two nos kits so we can have multi stage activation which will be all done with flex tables!
- Holden202T
- Posts: 10311
- Joined: Sat Feb 28, 2009 9:05 pm
- Location: Tenambit, NSW
- Contact:
Re: Flex output ?
why ? .... see signature
No matter what the question is, the answer is always more horsepower!
Just starting out? Have a read of the getting started guide
Basic tuning of a delco ECM with $12P thread
Advanced tuning of a delco ECM with $12P thread
Just starting out? Have a read of the getting started guide
Basic tuning of a delco ECM with $12P thread
Advanced tuning of a delco ECM with $12P thread
- TdracerTd
- Posts: 488
- Joined: Mon Aug 19, 2013 10:39 pm
- cars: Td Gemini coupe (race car WIP)
Holden VE SS ute (tow car/daily)
Vp commodore V6 (race car, s/c, e85, intercooled)
Jeep Grand Cherokee Overland (mrs car, family bus)
My12 subaru STi (Weekend warrior/Toy)
1972 LJ torana GTR (my Dad's car)
Mitsubishi Evo IX
Re: Flex output ?
Are the pwm drivers still available?