ecotec S/C v6 with 808 ecu
ecotec S/C v6 with 808 ecu
hi has anyone used the 808 to run the S/C six?
rgds
rob
currently thinking of replacing the ecotec in the hilux but keeping the hyd trans TH700
rgds
rob
currently thinking of replacing the ecotec in the hilux but keeping the hyd trans TH700
- krusty
- Posts: 570
- Joined: Wed Jan 27, 2010 9:45 pm
- cars: VY Calais guzzler, Toyota Corolla almost hybrid
- Location: Melbourne, VIC
Re: ecotec S/C v6 with 808 ecu
Yeah it's been done and can work well
I'm guessing you have a V6 running 808 currently? If so a super 6 on 808 woudl work well witht the right tune
If it's a fresh conversion going in the VS or VT super6 pcm and loom would be my pick. Gives you sequential injection which helps a lot on super6. Batch and super6 gives a bit of rough idle but isn't the end of the world and 808$12P has some cool features too
I'm guessing you have a V6 running 808 currently? If so a super 6 on 808 woudl work well witht the right tune
If it's a fresh conversion going in the VS or VT super6 pcm and loom would be my pick. Gives you sequential injection which helps a lot on super6. Batch and super6 gives a bit of rough idle but isn't the end of the world and 808$12P has some cool features too
-
- Posts: 2882
- Joined: Sun Aug 02, 2009 9:16 pm
- Location: Bayside, Melbourne, Victoria
- Contact:
Re: ecotec S/C v6 with 808 ecu
I could have sworn the were some base L67 files in the $12p & $11p threads?
I know you have a hydraulic trans so you only need $12p but was pretty sure there was a base $11p L67 file in 1 of the releases.
If there's no other replies I'll see if I can do a base $12p starting file for you when I get some spare time!
I know you have a hydraulic trans so you only need $12p but was pretty sure there was a base $11p L67 file in 1 of the releases.
If there's no other replies I'll see if I can do a base $12p starting file for you when I get some spare time!
-
- Posts: 2882
- Joined: Sun Aug 02, 2009 9:16 pm
- Location: Bayside, Melbourne, Victoria
- Contact:
Re: ecotec S/C v6 with 808 ecu
O.K. I found the L67 file from $11p & copied all noticeable differences to the $12p V6 file & should get you in the ball park!
I know when I did the $11p on a stock engine it wasn't very good so you will need to be able to log & adjust off log's & then will need a wideband to tune properly!
I know when I did the $11p on a stock engine it wasn't very good so you will need to be able to log & adjust off log's & then will need a wideband to tune properly!
- Attachments
-
- OSE $12P V112 APNX V6.log
- (381 Bytes) Downloaded 212 times
-
- OSE $12P V112 APNX V6-L67.log
- (3.85 KiB) Downloaded 211 times
-
- OSE $12P V112 APNX V6-L67.BIN
- (32 KiB) Downloaded 222 times
-
- OSE $12P V112 APNX V6.BIN
- (32 KiB) Downloaded 218 times
-
- OSE12P V112 - 1,2 and 3 bar.xdf
- (406.8 KiB) Downloaded 221 times
- Holden202T
- Posts: 10311
- Joined: Sat Feb 28, 2009 9:05 pm
- Location: Tenambit, NSW
- Contact:
Re: ecotec S/C v6 with 808 ecu
don't spend too much time on it yet vx l67 getrag, hes only just finished putting the ecotec in so the L67 conversion is probably just a thought at the moment!
No matter what the question is, the answer is always more horsepower!
Just starting out? Have a read of the getting started guide
Basic tuning of a delco ECM with $12P thread
Advanced tuning of a delco ECM with $12P thread
Just starting out? Have a read of the getting started guide
Basic tuning of a delco ECM with $12P thread
Advanced tuning of a delco ECM with $12P thread
-
- Posts: 11
- Joined: Wed Jul 27, 2011 10:03 pm
- cars: vp commodore v6
Re: ecotec S/C v6 with 808 ecu
Wonder if this will work with what I want to do.
-
- Posts: 11
- Joined: Wed Jul 27, 2011 10:03 pm
- cars: vp commodore v6
Re: ecotec S/C v6 with 808 ecu
would this tune work on a vr manual computer to run a super 6. and will it run with a map instead of a maf.
-
- Posts: 2882
- Joined: Sun Aug 02, 2009 9:16 pm
- Location: Bayside, Melbourne, Victoria
- Contact:
Re: ecotec S/C v6 with 808 ecu
It will but it's not guaranteed to work straight off the bat, you'll need to log & adjust from memory I had to change the injector rate a bit for stock L67 injectors (from memory it was too rich).
-
- Posts: 11
- Joined: Wed Jul 27, 2011 10:03 pm
- cars: vp commodore v6
Re: ecotec S/C v6 with 808 ecu
very nice. i wanted to use the vr harness and now it looks like i can. where is best place to plumb in map. and witch bin do i use. as there is 2. i assume the one that says l67. sorry i am new to doing this..
-
- Posts: 11
- Joined: Wed Jul 27, 2011 10:03 pm
- cars: vp commodore v6
Re: ecotec S/C v6 with 808 ecu
any info i could get would be great. as i have just found a donor vt super6 car.