VT V6 into Gemini
Re: VT V6 into Gemini
a friend of mine is running this big stepper motor box with a speedo cable output... fully calbiratable and drives your factory dash speedo cable. pretty dear tho, at a few hundred bucks.
-
- Posts: 34
- Joined: Sun May 08, 2016 11:34 am
- cars: 81 Mitsubishi Sigma EFI 351
83 Gemini ute 3.8 v6 (under construction)
2013 Focus ST - Location: Shoalhaven
Re: VT V6 into Gemini
Yeah might pull the guts out of the new speedo and fit it into the gem cluster (somehow)Holden202T wrote:when i did the ecotec into Torana i used a very similar speedo, easy to configure and works well, but obviously depends if you want to keep the dash looking stock or not!
what are the two plates to the right of the sump for ?
The plates are part of the engine mounts
Re: VT V6 into Gemini
HQ355 recently done something similair with the VN speedo drive on the standard HQ mechanical drive for the needle. Well worth looking into.
- vlad01
- Posts: 7795
- Joined: Mon Oct 08, 2012 6:41 pm
- cars: VP I S
VP I executive
VP II executive
VP II executive #2
VR II executive - Location: Kyneton, Vic
Re: VT V6 into Gemini
its actually a whole VP speedo with the HQ face and housing and setup on T56 via festy's converter to give square wave for the speedo and 808
I'm the director of VSH (Vlad's Spec Holden), because HSV were doing it ass about.
-
- Posts: 34
- Joined: Sun May 08, 2016 11:34 am
- cars: 81 Mitsubishi Sigma EFI 351
83 Gemini ute 3.8 v6 (under construction)
2013 Focus ST - Location: Shoalhaven
Re: VT V6 into Gemini
engine and box is mounted up
No cutting the trans tunnel, just had to cut the lift tabs off the sides of the box and a little tap around the passenger side to clear the selector shaft
No cutting the trans tunnel, just had to cut the lift tabs off the sides of the box and a little tap around the passenger side to clear the selector shaft
Re: VT V6 into Gemini
Any pictures?
-
- Posts: 34
- Joined: Sun May 08, 2016 11:34 am
- cars: 81 Mitsubishi Sigma EFI 351
83 Gemini ute 3.8 v6 (under construction)
2013 Focus ST - Location: Shoalhaven
Re: VT V6 into Gemini
MAGP wrote:Any pictures?
Only some dummy up pics
This was before and hammering was done, engine had to go back 40mm
but as you can see there's a massive amount of room around the trans
Re: VT V6 into Gemini
Looks good, no problem with room around the back of the block.
Much room at the front?
Much room at the front?
-
- Posts: 34
- Joined: Sun May 08, 2016 11:34 am
- cars: 81 Mitsubishi Sigma EFI 351
83 Gemini ute 3.8 v6 (under construction)
2013 Focus ST - Location: Shoalhaven
Re: VT V6 into Gemini
Heaps of room around the engine, just tight around the passenger side of the transMAGP wrote:Looks good, no problem with room around the back of the block.
Much room at the front?
- Holden202T
- Posts: 10311
- Joined: Sat Feb 28, 2009 9:05 pm
- Location: Tenambit, NSW
- Contact:
Re: VT V6 into Gemini
hard to tell from that angle but it looks like the engine is further forward than firebugs.
No matter what the question is, the answer is always more horsepower!
Just starting out? Have a read of the getting started guide
Basic tuning of a delco ECM with $12P thread
Advanced tuning of a delco ECM with $12P thread
Just starting out? Have a read of the getting started guide
Basic tuning of a delco ECM with $12P thread
Advanced tuning of a delco ECM with $12P thread