What do I need for a complete tuning set?

[MAGP]

Thanks for that Antus, it been ages since I worked for GMH so I was relying on memory. I've adjusted my list on my computer and will adjust the list in the post now. I'll take a look at ebay and see what is available so I can work out a budget.

[Dylan]

I have a spare 082 I can part with. That'll cover a few model's.

[vlad01]

pick a part, pick a part, pick a part......

[MAGP]

I have a spare 082 I can part with. That'll cover a few model's.

How much would you like for it? and is it already converted?

[Dylan]

It's untouched but I can add in the write line for you to suit NVRAM no problem.
PM me if you're interested it's just in the cupboard doing nothing.

[antus]

This list will help for pcm service numbers http://pcmhacking.net/memcals.html

[delcowizzid]

this https://pcmhacking.net/forums/viewto ... =14&t=3613
and this https://pcmhacking.net/forums/viewto ... =14&t=3612
wil cover the 808 ecu for vn vp vr manual and vs v8 manual and along with a 424 vr auto ecu with the write line wire added will cover vr and vs auto needs bar ecotec (cable below to allow tuning 424 via aldl plug under colomn)
this https://pcmhacking.net/forums/viewto ... =14&t=3616
will cover the 424 comms as stated above for tuning and tuning of vs ecotech to vy ecu's up the aldl port along with the board below
this https://pcmhacking.net/forums/viewto ... =14&t=3617
will cover all ecotech models and vs series 3 v8 and vt v8 with the appropriate software on the nvram for each model of you could have an nvram for each model ready to insert in the board for faster swapping instead of burning the nvram for swapping between models.

so you need 1 808 to convert with comms and add a write line wire and one 424 ecu to add a write line wire all other models can be tuned with the customers own ecu with nvram board fitted and then a memcal burnt when finished

[MAGP]

This list will help for pcm service numbers http://pcmhacking.net/memcals.html

I have just adjusted the list I did before it now has all the options taken from that link. Probably much easier to reference than the memcals page if people just need the ECM/PCM numbers.

[MAGP]

this https://pcmhacking.net/forums/viewto ... =14&t=3613
and this https://pcmhacking.net/forums/viewto ... =14&t=3612
wil cover the 808 ecu for vn vp vr manual and vs v8 manual and along with a 424 vr auto ecu with the write line wire added will cover vr and vs auto needs bar ecotec (cable below to allow tuning 424 via aldl plug under colomn)
this https://pcmhacking.net/forums/viewto ... =14&t=3616
will cover the 424 comms as stated above for tuning and tuning of vs ecotech to vy ecu's up the aldl port along with the board below
this https://pcmhacking.net/forums/viewto ... =14&t=3617
will cover all ecotech models and vs series 3 v8 and vt v8 with the appropriate software on the nvram for each model of you could have an nvram for each model ready to insert in the board for faster swapping instead of burning the nvram for swapping between models.

so you need 1 808 to convert with comms and add a write line wire and one 424 ecu to add a write line wire all other models can be tuned with the customers own ecu with nvram board fitted and then a memcal burnt when finished

Thanks for that, I will contact the relevant people via PM early next week and get things organised.