LC-1 Wide band sensor
-
- Posts: 1841
- Joined: Sat Aug 06, 2011 7:58 am
- cars: V8 VR Commodore BT1
LB Lancer 2L turbo & Delco
Starion TBI with Delco
Mitsubishi Lancer EVO4 track car
NA MX5
3 vintage motor bikes - Location: Padstow NSW
Re: LC-1 Wide band sensor
Is that a US website? Our dollar is worth around 74 cents.
-
- Posts: 1841
- Joined: Sat Aug 06, 2011 7:58 am
- cars: V8 VR Commodore BT1
LB Lancer 2L turbo & Delco
Starion TBI with Delco
Mitsubishi Lancer EVO4 track car
NA MX5
3 vintage motor bikes - Location: Padstow NSW
Re: LC-1 Wide band sensor
Oh I think you mean they are both 4.2. Funny I have a LM2 and it takes the 4.2 and also a LC1 and it uses the 4.9. That's what I was going off.
Re: LC-1 Wide band sensor
????????Charlescrown wrote:Is that a US website? Our dollar is worth around 74 cents.
Nope, I mean you need to check the manufacturers website to see what is required. The manufacturers says the LC-1 uses the 4.2. I never said anything about the 4.9, LM2 or anythign else.Charlescrown wrote:Oh I think you mean they are both 4.2.
Charlescrown wrote:Funny I have a LM2 and it takes the 4.2 and also a LC1 and it uses the 4.9. That's what I was going off.
-
- Posts: 1841
- Joined: Sat Aug 06, 2011 7:58 am
- cars: V8 VR Commodore BT1
LB Lancer 2L turbo & Delco
Starion TBI with Delco
Mitsubishi Lancer EVO4 track car
NA MX5
3 vintage motor bikes - Location: Padstow NSW
Re: LC-1 Wide band sensor
Sorry my mistake. If the LC1 uses the 4.2 then the first Holden number 12575904 should fit. I use one now for my LM2 after I ran over the original one supplied by Innovate the only difference is the cable was a little shorter.
- Holden202T
- Posts: 10328
- Joined: Sat Feb 28, 2009 9:05 pm
- Location: Tenambit, NSW
- Contact:
Re: LC-1 Wide band sensor
I think the LC2 uses the 4.9 ? I have a 4.9 kit for my MTX-L haven't used it yet though.
No matter what the question is, the answer is always more horsepower!
Just starting out? Have a read of the getting started guide
Basic tuning of a delco ECM with $12P thread
Advanced tuning of a delco ECM with $12P thread
Just starting out? Have a read of the getting started guide
Basic tuning of a delco ECM with $12P thread
Advanced tuning of a delco ECM with $12P thread
Re: LC-1 Wide band sensor
My LC-1 uses a 4.2, they did revise it at some stage but not sure if it was renamed or not
-
- Posts: 1841
- Joined: Sat Aug 06, 2011 7:58 am
- cars: V8 VR Commodore BT1
LB Lancer 2L turbo & Delco
Starion TBI with Delco
Mitsubishi Lancer EVO4 track car
NA MX5
3 vintage motor bikes - Location: Padstow NSW
Re: LC-1 Wide band sensor
I know my LM2 can be upgraded to the 4.9 with a software and cable change but if so many manufacturers use the 4.2 and they last I don't see the need for the upgrade.
- Holden202T
- Posts: 10328
- Joined: Sat Feb 28, 2009 9:05 pm
- Location: Tenambit, NSW
- Contact:
Re: LC-1 Wide band sensor
Yeah my MTX-L was the same upgrade.
No matter what the question is, the answer is always more horsepower!
Just starting out? Have a read of the getting started guide
Basic tuning of a delco ECM with $12P thread
Advanced tuning of a delco ECM with $12P thread
Just starting out? Have a read of the getting started guide
Basic tuning of a delco ECM with $12P thread
Advanced tuning of a delco ECM with $12P thread