0x1 GM_P4_ECM Imported Checksum 0x8 0x7FFF 0x6 0x0 PROMIDA: EPROM ID number 0 0 DATECODE: EPROM date code 0 0 SEQNUMB: Production Sequence number 0 0 KKPGMID: Check sum $5000 through $ffff 0 0 KKKPGMID: Program ID word - $12=1993 - $AA=bypass sumcheck 3 0 0 KRPMUP: RPM Threshold for engine running (EST) RPM 0 0 KERUNCTR: number of succ refpers to allow eng run Ref 0 0 KFUELUP: RPM Threshold for run fuel mode RPM 0 0 KRUNFCTR: number of succ refpers to allow run fuel mode Ref 0 0 KNUMCYLS: Number of engine cylinders (6 or 8) cyls 0 0 KFILTMP1: MAP params - MAP filter coefficient - Engine running Coeff 0 0 KKPMDF: MAP params - Default MAP reading for engine not running kPa 0 0 KKA: MAP params - Default MAP multiplier Coeff 0 0 KKB: MAP params - Default MAP offset constant term kPa 0 0 KKC: MAP params - RPM multiplier for default MAP calc kPa 0 0 KDMPRPMX: MAP params - RPM offset term for default MAP calculation kPa 0 0 KDMAPLL: MAP params - Default MAP lower limit kPa 0 0 KKACMAP: MAP params - Default MAP offset - A/C On kPa 0 0 KKDRMAP: MAP params - Default MAP offset - Drive or Reverse kPa 0 0 KDMAPIAC: MAP params - Nominal IAC position for normal idle Steps 0 0 KDMIACGN: MAP params - IAC gain factor factor 0 0 KDMPFLTI: MAP params - Default MAP filter coefficient - Increasing Coeff 0 0 KDMPFLTD: MAP params - Default MAP filter coefficient - Decreasing Coeff 0 0 KTPCLOSE: TPS - TPS Closed throttle threshold (EGR port) % 0 0 KF4CNTR: TPS - F4 flag throttle opening delay % 0 0 K3: TPS - TPS Full travel - Worst case minimum voltage Volts 0 0 KTAOFF: TPS - Closed TPS filter coefficient Coeff 0 0 KTPSHYST: TPS - TPS Hysteresis value Cnt 0 0 KSPDSENA: Road speed params - Speed sensor constant Pulses/Kilometre PPK 0 0 KFILTKPH: Road speed params - Lag filter coefficient for KPH N.D Coeff 0 0 KREFANGL: EST params - Spark reference angle Deg 0 0 KTIMELAG: EST params - Time domain correction to spark Usec 0 0 KMAXADV: EST params - Maximum Spark Advance from TDC Deg 0 0 KMAXRTD: EST params - Maximum Spark Retard from TDC Deg 0 0 KBYPSPK: EST params - Bypass Mode Forced Advance Deg 0 0 KDFCOADV: EST params - DFCO Mode Forced Advance Deg 0 0 KDFCODCV: EST params - DFCO spark ram out rate Deg/S 0 0 KDIAGADV: EST params - DIAG Mode Forced Advance Deg 0 0 KDIAGRPM: EST params - Maximum RPM for KDIAGADV RPM 0 0 KDYNGAIN: EST params - Dynamic correction factor FACTOR 0 0 KDYNDB: EST params - Dynamic correction delta ref deadband Msec 0 0 KADVLIM: EST params - Max rate of Advance increase except in DE Deg/S 0 0 KADVSLOP: EST params - F1 table Extension Slope Deg/K 0 0 KCTBIAS: EST params - F2 Table Bias Term Deg 0 0 KTMRPM: EST params - Torque management RPM threshold RPM 0 0 KTMADV: EST params - Torque management Forced Advance Deg 0 0 KDYNDB: EST params - Dwell during 18X crank spark Msec 0 0 KESCOOLA: ESC params - Coolant temp enable DegC 0 0 KESCTIM: ESC params - Engine Run Time to Enable Sec 0 0 KESCRPML: ESC params - Minimum RPM to Increase Retard RPM 0 0 KESCRPMH: ESC params - Maximum RPM to Increase Retard RPM 0 0 KRETMAX: ESC params - Maximum Retard Deg 0 0 KBKRCLT: Burst Knock Retard - If coolant < This then skip Burst knock DegC 0 0 KBKRRPM: Burst Knock Retard - If RPM > Cal then Zero BKRTD RPM 0 0 KBKRTPS: Burst Knock Retard - TPS Delta threshold to activate BKRTD % 0 0 KBKRRFLO: Burst Knock Retard - If REFS in BKRTD <= Cal then Zero BKRTD REFPSL 0 0 KBKRRFHI: Burst Knock Retard - If REFS in BKRTD >= Cal then Zero BKRTD REFPSL 0 0 KBKRTD: Burst Knock Retard - Burst Knock Retard active value Deg 0 0 KBKRDEC: Burst Knock Retard - BKRTD decay value Deg 0 0 KLOTPSBK: Burst Knock Retard - If TPSENG <= CAL then set TPSENG12 = 0 % 0 0 KBKFCRNK: Backfire Inhibit - Threshold for Crank Input Volts 0 0 KBKFRPM: Backfire Inhibit - RPM threshold for fuel cutoff RPM 0 0 KBKFTEMP: Backfire Inhibit - Temperature Threshold for Fuel Cutoff DegC 0 0 KRPMRDSC: RDSC - High resolution RPM filter coefficient Coef 0 0 KRDSMIN: RDSC - Spark advance RDSC lower limit Deg 0 0 KTPSDLT: RDSC - Increasing/Decreasing TPS threshold % 0 0 KRDSCTPS: RDSC - Low/High TPS threshold for RDSC % 0 0 KRDSTPSH: RDSC - Disable RDSC logic if NTPSLD > KRDSTPSH % 0 0 KRDSCCLT: RDSC - Disable RDSC logic if COOLDEG < KRDSCCLT DegC 0 0 KRDSKPHL: RDSC - Disable RDSC logic if FILTKPH <= KRDSKPHL KPH 0 0 KRDSRPMH: RDSC - Disable RDSC logic if NTRPMX >= KRDSRPMH RPM 0 0 KRDSRPML: RDSC - Disable RDSC logic if NTRPMX < KRDSRPML RPM 0 0 KINGAIN1: RDSC - RDSC1 Tip-In gain amount for 1st gear Deg/RPM 0 0 KINGAIN2: RDSC - RDSC1 Tip-In gain amount for 2nd gear Deg/RPM 0 0 KINGAIN3: RDSC - RDSC1 Tip-In gain amount for 3rd gear Deg/RPM 0 0 KINGAIN4: RDSC - RDSC1 Tip-In gain amount for 4th gear Deg/RPM 0 0 KINGAIN5: RDSC - RDSC1 Tip-In gain amount for 5th gear Deg/RPM 0 0 KINGAINN: RDSC - RDSC1 Tip-In gain amount for Neutral Deg/RPM 0 0 KINNEG: RDSC - RDSC1 Tip-In - Spark RDSC negative change limit Deg 0 0 KINPOS: RDSC - RDSC1 Tip-In - Spark RDSC positive change limit Deg 0 0 KINCTR1: RDSC - RDSC1 Tip-In - Time RDSC1 enabled when increasing TPS Sec 0 0 KOUGAIN1: RDSC - RDSC Tip-Out gain amount for 1st gear Deg/RPM 0 0 KOUGAIN2: RDSC - RDSC1 Tip-Out gain amount for 2nd gear Deg/RPM 0 0 KOUGAIN3: RDSC - RDSC1 Tip-Out gain amount for 3rd gear Deg/RPM 0 0 KOUGAIN4: RDSC - RDSC1 Tip-Out gain amount for 4th gear Deg/RPM 0 0 KOUGAIN5: RDSC - RDSC1 Tip-Out gain amount for 5th gear Deg/RPM 0 0 KOUGAINN: RDSC - RDSC1 Tip-Out gain amount for Neutral Deg/RPM 0 0 KOUTCTR: RDSC1 - RDSC1 Tip-Out - Time RDSC1 enabled when decreasing TPS Sec 0 0 KOUTNEG: RDSC - RDSC1 Tip-Out - Spark RDSC negative change limit Deg 0 0 KOUTPOS: RDSC - RDSC1 Tip-In - Spark RDSC positive change limit Deg 0 0 KBMPKPH: Tip-In Bump - Minimum vehicle speed to enable Bump spark KPH 0 0 KBMPACT: Tip-In Bump - Time bump spark is active Sec 0 0 KBMPDLY: Tip-In Bump - Time bump spark is held steady before decay Sec 0 0 KBMPGEAR: Tip-In Bump - Time bump spark not allowed after gear change Sec 0 0 KBMPBIAS: Tip-In Bump - Table bias for Bump Spark Deg 0 0 KBUMPMAX: Tip-In Bump - Upper Bump Spark Limit (add KBMPBIAS) Deg 0 0 KINGAINI: Idle Drive - Idle drive gain amount Fact 0 0 KINNEGI: Idle Drive - Idle drive Negative change limit (Tip-In) Deg 0 0 KINPOSI: Idle Drive - Idle drive Positive change limit (Tip-In) Deg 0 0 KROLLRPM: Idle Drive - Idle RDSC Enable RPM threshold RPM 0 0 KINJFLOW: Run A/F Param - Displacement/inj flow rate; (Litres/Grams per se Grams/Sec 0 0 KAPLH: Run A/F Param - Minimum BPW hysteresis value Msec 0 0 KAPLL: Run A/F Param - Minimum BPW for Sync delivery Msec 0 0 KAPMIN: Run A/F Param - Minimum Asynchronous pulse width Msec 0 0 KAPMAX: Run A/F Param - Maximum Asynchronous pulse width Msec 0 0 KFCORPML: Run A/F Param - High RPM Fuel cutoff - Low Limit RPM 0 0 KFCORPMH: Run A/F Param - High RPM Fuel cutoff - High Limit RPM 0 0 KFCOKPHL: Run A/F Param - High Speed Fuel cutoff - Low Limit KPH 0 0 KFCOKPHH: Run A/F Param - High Speed Fuel cutoff - High Limit KPH 0 0 KFCOTIME: Run A/F Param - Fuel cutoff time threshold Sec 0 0 KAFSTCN: Run A/F Param - Stoichiometric A/F ratio Ratio 0 0 KAFTCTH: Run A/F Param - Max coolant temp for F56 A/F Ratio DegC 0 0 KAFDM: Run A/F Param - A/F Time out decay multiplier % 0 0 KLCCLT: Lean Cruise Param - Minimum coolant temp for Lean Cruise DegC 0 0 KLCSPD: Lean Cruise Param - Minimum vehicle speed for Lean Cruise KPH 0 0 KAFLCTIM: Lean Cruise Param - Time delay after idle for Lean Cruise Sec 0 0 KAFSTEP: Lean Cruise Param - Delay time before Lean Cruise A/F step Sec 0 0 KIDLEKPH: Idle Fuel Param - Max road speed for idle A/F ratio KPH 0 0 KFILTCLT: Idle Fuel Param - Coolant temp filter coeff at idle Coef 0 0 KIDLTIMN: Idle Fuel Param - Delay before using idle A/F ratio(manual & Aut Sec 0 0 KIDLTIMA: Idle Fuel Param - Delay before using idle A/F ratio (Auto in P/N Sec 0 0 KLEMGAIN: Idle Fuel Param - Lowspeed enrichment multiplier gain %/100 0 0 KLEMMAX: Idle Fuel Param - Lowspeed enrichment multiplier Maximum Factor 0 0 KLEMRPM: Idle Fuel Param - RPM above desired to begin Lowspeed enrichment RPM 0 0 KFILTVE: Idle Fuel Param - VE table filter coefficient at idle Coeff 0 0 KVEFLRPM: Idle Fuel Param - RPM threshold for filtering VE RPM 0 0 KCFTM0: Crank A/F Param - Number of ref pulses before crank fuel dacay (se Pulses 0 0 KCFTM1: Crank A/F Param - Number of ref pulses before crank fuel decay Pulses 0 0 KCFTM2: Crank A/F Param - Number of ref pulses between crank decay loops Pulses 0 0 KAFCFTA: Crank A/F Param - Clear flood throttle limit TPSENG units % 0 0 KTPSMAX: Crank A/F Param - High TPS for selecting crank BPW AD cnts 0 0 KCRSTEP: Crank A/F Param - Crank decay step size Msec 0 0 KCRMIN: Crank A/F Param - Minimum crank BPW Msec 0 0 KAEDFTHR: Manifold Fuel Param - AE delta fuel threshold MANFUEL 0 0 KMANRPM: Manifold Fuel Param - RPM gain factor for MANFUEL calc Factor 0 0 KAEFLT: Manifold Fuel Param - Filter coefficient for increasing MANFUEL Coeff 0 0 KDEFLT: Manifold Fuel Param - Filter coefficient for decreasing MANFUEL Coeff 0 0 KAETATH: Accel Enrichment Param - AE delta throttle threshold TPSENG uni % 0 0 KAEISCN: Accel Enrichment Param - AE Idle air control contribution Msec 0 0 KITPSCFA: Accel Enrichment Param - AE increasing TPS filter coefficient Coeff 0 0 KDTPSCFA: Accel Enrichment Param - AE decreasing TPS filter coefficient Coeff 0 0 KDEDFTH: Decel Enleanment Param - DE delta fuel threshold MANFUEL 0 0 KDEDFTH: Decel Enleanment Param - DE delta throttle angle threshold % 0 0 KDETATH: Decel Enleanment Param - Delta TPS DE factor Mult 0 0 KDEDKTH: Decel Enleanment Param - DE throttle decay factor %/Ref 0 0 KITPSCFD: Decel Enleanment Param - DE Increasing TPS filter coefficient Coeff 0 0 KDTPSCFD: Decel Enleanment Param - DE Decreasing TPS filter coefficient Coeff 0 0 KBPWMIN: Decel Enleanment Param - DE throttle decay factor Msec 0 0 KDFCOSPH: DFCO Params - DFCO Upper RPM limit - NTRPMX units RPM 0 0 KDFCOSPH: DFCO Params - DFCO Lower RPM limit - NTRPMX units RPM 0 0 KDFMAPA: DFCO Params - DFCO Max MAP for Automatic (add 8Kpa hysteresis) Kpa 0 0 KDFMAPM: DFCO Params - DFCO Max MAP for Manual (add 8Kpa hysteresis) Kpa 0 0 KDFCOG: DFCO Params - DFCO Multiplier step value % 0 0 KDFCOSLL: DFCO Params - DFCO Road speed threshold ( + 5kph hysteresis) KPH 0 0 KDFCOTP: DFCO Params - DFCO Throttle threshold % 0 0 KDFCOPW: DFCO Params - DFCO Asynch AE multiplier to BPW Gain 0 0 KDFCOCLT: DFCO Params - DFCO Temperature threshold DegC 0 0 KVETCLL: VE Learn Params - VE Learn Low temperature limit DegC 0 0 KVETCLH: VE Learn Params - VE Learn High temperature limit DegC 0 0 KVEESRAD: VE Learn Params - VE Learn Window - RPM Radius (7 MAX) RPM 0 0 KVEPMRAD: VE Learn Params - VE Learn Window - MAP Radius (15 MAX) Kpa 0 0 KVEMIN: VE Learn Params - Minimum VE Value % 0 0 KVEITTH: VE Learn Params - Learning Integrator window Units 0 0 KVETIME: VE Learn Params - Learn control update rate Sec 0 0 1st UNKNOWN CHANGE 5F to FF Sec 0 0 KBATOOR: IAC Params - Battery voltage Out-of-Range time threshold Sec 0 0 KISTPSI: IAC Params - Maximum throttle position for idle % 0 0 KRSTRPM: IAC Params - IAC motor reset RPM threshold RPM 0 0 KMAXBASD: IAC Params - Maximum base parameter - Drive Steps 0 0 KMAXBASN: IAC Params - Maximum base parameter - Neutral Steps 0 0 KMAXBASA: IAC Params - Maximum base parameter - A/C Steps 0 0 KISSWNA: IAC Params - Initial IAC motor position Steps 0 0 KACDLD: IAC Params - Initial additional A/C steps Steps 0 0 KISPKDL: IAC Params - Ignition off park delta from base Steps 0 0 KISPKHOT: IAC Params - Hot crank park delta from base Steps 0 0 KISPKCLT: IAC Params - Temperature Threshold for Park Delta DegC 0 0 KPNDELAY: IAC Params - IAC Base Delay for Drive to Park/Neutral Sec 0 0 KIACMAP: IAC Params - Maximum MAP load limit kPa 0 0 KIACMXMP: IAC Params - Maximum Motor position Steps 0 0 KETCDLTA: IAC - Adjustments - Extended throttle crack delta Steps 0 0 KIACCL: IAC - Adjustments - Closed loop fuel step increase Steps 0 0 KHFANDS: IAC - Adjustments - High speed fan-on transient IAC steps Steps 0 0 KHFANCLC: IAC - Adjustments - Time before High fan transient IAC steps are Secs 0 0 KHIACFAN: IAC - Adjustments - High speed fan-on IAC step increase Steps 0 0 KLFANDS: IAC - Adjustments - Low speed fan-on transient IAC steps Steps 0 0 KLFANCLC: IAC - Adjustments - Time before Low fan transient IAC steps are Secs 0 0 KLIACFAN: IAC - Adjustments - Low speed fan-on IAC step increase Steps 0 0 KIACDM: IAC - warm-up params - IAC decay multiplier value % 0 0 KDRMULT: IAC - warm-up params - RPM Warm-up offset factor for drive % 0 0 KF14DM1: IAC - warm-up params - Time before Warm-up decay begins Sec 0 0 KISALPC: IAC - warm-up params - Initial Stall Saver IAC offset Steps 0 0 KISTDELC: IAC - warm-up params - Initial Stall Saver duration Sec 0 0 KLGDB: IAC - Closed loop params - Large Error RPM dead band RPM 0 0 KDRDB: IAC - Closed loop params - Drive RPM deadband RPM 0 0 KPNDB: IAC - Closed loop params - P/N or Manual RPM deadband RPM 0 0 KISDWADN: IAC - Closed loop params - Desired RPM increase for A/C ON RPM 0 0 KFILRPMH: IAC - Closed loop params - RPM filter coefficient when above des Coeff 0 0 KFILRPML: IAC - Closed loop params - RPM filter coefficient when below des Coeff 0 0 KOPENDEL: IAC - Closed loop params - Closed loop delay for opening throttl Sec 0 0 KPKDRDEL: IAC - Closed loop params - Closed loop delay for Park/Drive chan Sec 0 0 KACTRANS: IAC - Closed loop params - Closed loop delay for A/C change Sec 0 0 KRPMIDLE: IAC - Idle spark Adjustment params - High resolution idle RPM fi Coeff 0 0 KSACOOL: IAC - Idle spark Adjustment params - IAC spark correct'n lower co DegC 0 0 KSARPMHI: IAC - Idle spark Adjustment params - High RPM spark correction m %Deg/RPM 0 0 KSARPMLO: IAC - Idle spark Adjustment params - Low RPM spark correction mu %Deg/RPM 0 0 KSAOLDB: IAC - Idle spark Adjustment params - RPM error limit for spark ad RPM 0 0 KSCORLIM: IAC - Idle spark Adjustment params - Idle spark correction limit Deg 0 0 KTCDELTA: IAC - Transient IAC params - Throttle Crack Delta TPS % 0 0 KMLGAIN: IAC - Transient IAC params - MAP Limiter Gain Factor % 0 0 KMLMAX: IAC - Transient IAC params - MAP Limiter Maximum Offset Steps 0 0 KSSRPM: IAC - Transient IAC params - Stall Saver RPM Threshold RPM 0 0 KSAVSTEP: IAC - Transient IAC params - Stall Saver IAC Increase Steps 0 0 KSAGDB: IAC - Transient IAC params - Sag Mode Deadband RPM 0 0 KSAGSTEP: IAC - Transient IAC params - Sag Mode IAC Increase Steps 0 0 KADBARO: Baro params - Default Baro A/D counts (243 = 100kPa) kPa 0 0 KMAXOFF: Baro params - Maximum MAP offset for baro adjustment kPa 0 0 KNVRATAL: Shift light params - RPM/KmH N/V for 5th to be upshifted 0 0 KDLTRPMA: Shift light params - Engine speed tolerence for 5th gear RPM 0 0 KGEARDL1: Shift light params - In-Gear delay time for 1st gear Sec 0 0 KGEARDL2: Shift light params - In-Gear delay time for 2nd 3rd 4th & 5th ge Sec 0 0 KNVRATBL: Shift light params - RPM/KMH N/V for 4th gear 0 0 KDLTRPMB: Shift light params - Engine speed tolerence for 4th gear RPM 0 0 KSHFRPMB: Shift light params - Minimum RPM to allow shift to 5th gear RPM 0 0 KSHFMAPB: Shift light params - Maximum MAP to allow shift to 5th gear kPa 0 0 KNVRATCL: Shift light params - RPM/KMH N/V for 3rd gear 0 0 KDLTRPMC: Shift light params - Engine speed tolerence for 3rd gear RPM 0 0 KSHFRPMC: Shift light params - Minimum RPM to allow shift to 4th gear RPM 0 0 KSHFMAPC: Shift light params - Maximum MAP to allow shift to 4th gear kPa 0 0 KNVRATDL: Shift light params - RPM/KMH N/V for 2nd gear 0 0 KDLTRPMD: Shift light params - Engine speed tolerence for 2nd gear RPM 0 0 KSHFRPMD: Shift light params - Minimum RPM to allow shift to 3rd gear RPM 0 0 KSHFMAPD: Shift light params - Maximum MAP to allow shift to 3rd gear kPa 0 0 KNVRATEL: Shift light params - RPM/KMH N/V for 1st gear 0 0 KDLTRPME: Shift light params - Engine speed tolerence for 1st gear RPM 0 0 KSHFRPME: Shift light params - Minimum RPM to allow shift to 2nd gear RPM 0 0 KSHFMAPE: Shift light params - Maximum MAP to allow shift to 2nd gear kPa 0 0 KTCCTMPL: TCC lower temperature limit DegC 0 0 KCOASTHZ: TCC Params - TCC Hysteresis for KCOAST1 and KCOAST2 % 0 0 KRSCSTL: TCC Params - TCC Road speed coast level km/h 0 0 KCOAST1A: TCC Params - TCC Low km/h coast load limit % 0 0 KCOAST2A: TCC Params - TCC High km/h coast load limit % 0 0 KREL1A: TCC Params - TCC Negative delta Throttle position Unlock limit % 0 0 KREL2A: TCC Params - TCC Positive delta Throttle position unlock limit % 0 0 KLCKDLYT: TCC Params - TCC delay before lock enabled after coast Sec 0 0 KLKDLYT2: TCC Params - TCC Coast release lock delay time Low road speed Sec 0 0 KLKDLYT3: TCC Params - TCC Coast release lock delay time High road speed Sec 0 0 KRSHNTHL: TCC Params - TCC Road speed upper limit for LOCK km/h 0 0 KRSHNTLL: TCC Params - TCC Road speed lower limit for UNLOCK km/h 0 0 KHIFANTH: High speed fan ON coolant threshold -5deg hyst Deg C 0 0 KHIFANSP: Min road speed for High speed fan + 8kph hyst Kph 0 0 KHIFANTIM: Delay time before High fan turn on Sec 0 0 KLOFANTH: High speed fan ON coolant threshold -6deg hyst Deg C 0 0 KLOFANSP: Min road speed for Low speed fan + 8kph hyst Kph 0 0 KLOFANTIM: Delay time before Low fan turn on Sec 0 0 KACDISTP: A/C TPS Threshold for cut-out % 0 0 KACTIMER: A/C clutch - A/C delay time Secs 0 0 KACRPMHI: A/C clutch - A/C Clutch High RPM cut-out RPM 0 0 A/C CLUTCH - A/C Clutch re-enable RPM RPM 0 0 KTCFUEL:TRIP COMPUTER - AM'NT OF FUEL FOR 1/256 DU 0 0 KTCFUELR: TRIP COMPUTER - FUEL RATE USED Litres/Hr 0 0 3rd UNKNOWN CHANGE CE & 59 to 00 C8 Sec 0 0 4th UNKNOWN CHANGE Code change of some sort C7 29 to D6 F7 Sec 0 0 5th UNKNOWN CHANGE Code change of some sort C7 29 to D6 F7 Sec 0 0 6th UNKNOWN CHANGE Code change of some sort 00 00 to 36 86 Sec 0 0 7th UNKNOWN CHANGE Code change of some sort 00 00 00 00 to BD C7 C8 32 Sec 0 0 8th UNKNOWN CHANGE Code change of some sort 00 00 00 00 to C8 32 BD C7 Sec 0 0 9th UNKNOWN CHANGE Code change of some sort 00 00 to 29 39 Sec 0 0 10th UNKNOWN CHANGE Code change of some sort 06 to 00 Sec 0 0 KOPTFLG1: Option Word 1 Read ECU file in Notepad for Bit descriptions - Bit 7 - Bit 7 0x80 KOPTFLG1: Option Word 1 Read ECU file in Notepad for Bit descriptions - Bit 6 - Bit 6 0x40 KOPTFLG1: Option Word 1 Read ECU file in Notepad for Bit descriptions - Bit 5 - Bit 5 0x20 KOPTFLG1: Option Word 1 Read ECU file in Notepad for Bit descriptions - Bit 4 - Bit 4 0x10 KOPTFLG1: Option Word 1 Read ECU file in Notepad for Bit descriptions - Bit 3 - Bit 3 0x08 KOPTFLG1: Option Word 1 Read ECU file in Notepad for Bit descriptions - Bit 2 - Bit 2 0x04 KOPTFLG1: Option Word 1 Read ECU file in Notepad for Bit descriptions - Bit 1 - Bit 1 0x02 KOPTFLG1: Option Word 1 Read ECU file in Notepad for Bit descriptions - Bit 0 - Bit 0 0x01 KOPTFLG2: Option Word 2 Read ECU file in Notepad for Bit descriptions - Bit 7 - Bit 7 0x80 KOPTFLG2: Option Word 2 Read ECU file in Notepad for Bit descriptions - Bit 6 - Bit 6 0x40 KOPTFLG2: Option Word 2 Read ECU file in Notepad for Bit descriptions - Bit 5 - Bit 5 0x20 KOPTFLG2: Option Word 2 Read ECU file in Notepad for Bit descriptions - Bit 4 - Bit 4 0x10 KOPTFLG2: Option Word 2 Read ECU file in Notepad for Bit descriptions - Bit 3 - Bit 3 0x08 KOPTFLG2: Option Word 2 Read ECU file in Notepad for Bit descriptions - Bit 2 - Bit 2 0x04 KOPTFLG2: Option Word 2 Read ECU file in Notepad for Bit descriptions - Bit 1 - Bit 1 0x02 KOPTFLG2: Option Word 2 Read ECU file in Notepad for Bit descriptions - Bit 0 - Bit 0 0x01 KOPTFLG3: Option Word 3 Read ECU file in Notepad for Bit descriptions - Bit 7 - Bit 7 0x80 KOPTFLG3: Option Word 3 Read ECU file in Notepad for Bit descriptions - Bit 6 - Bit 6 0x40 KOPTFLG3: Option Word 3 Read ECU file in Notepad for Bit descriptions - Bit 5 - Bit 5 0x20 KOPTFLG3: Option Word 3 Read ECU file in Notepad for Bit descriptions - Bit 4 - Bit 4 0x10 KOPTFLG3: Option Word 3 Read ECU file in Notepad for Bit descriptions - Bit 3 - Bit 3 0x08 KOPTFLG3: Option Word 3 Read ECU file in Notepad for Bit descriptions - Bit 2 - Bit 2 0x04 KOPTFLG3: Option Word 3 Read ECU file in Notepad for Bit descriptions - Bit 1 - Bit 1 0x02 KOPTFLG3: Option Word 3 Read ECU file in Notepad for Bit descriptions - Bit 0 - Bit 0 0x01 KOPTFLG4: Option Word 4 Read ECU file in Notepad for Bit descriptions - Bit 7 - Bit 7 0x80 KOPTFLG4: Option Word 4 Read ECU file in Notepad for Bit descriptions - Bit 6 - Bit 6 0x40 KOPTFLG4: Option Word 4 Read ECU file in Notepad for Bit descriptions - Bit 5 - Bit 5 0x20 KOPTFLG4: Option Word 4 Read ECU file in Notepad for Bit descriptions - Bit 4 - Bit 4 0x10 KOPTFLG4: Option Word 4 Read ECU file in Notepad for Bit descriptions - Bit 3 - Bit 3 0x08 KOPTFLG4: Option Word 4 Read ECU file in Notepad for Bit descriptions - Bit 2 - Bit 2 0x04 KOPTFLG4: Option Word 4 Read ECU file in Notepad for Bit descriptions - Bit 1 - Bit 1 0x02 KOPTFLG4: Option Word 4 Read ECU file in Notepad for Bit descriptions - Bit 0 - Bit 0 0x01 KKMASK1: MALFUNCTION FLAG - WORD 1 - Bit 7 - 13 0x80 KKMASK1: MALFUNCTION FLAG - WORD 1 - Bit 6 - 14 0x40 KKMASK1: MALFUNCTION FLAG - WORD 1 - Bit 5 - 15 0x20 KKMASK1: MALFUNCTION FLAG - WORD 1 - Bit 4 - 16 0x10 KKMASK1: MALFUNCTION FLAG - WORD 1 - Bit 3 - 17 0x08 KKMASK1: MALFUNCTION FLAG - WORD 1 - Bit 2 - 18 0x04 KKMASK1: MALFUNCTION FLAG - WORD 1 - Bit 1 - 19 0x02 KKMASK1: MALFUNCTION FLAG - WORD 1 - Bit 0 - 21 0x01 KKMASK2: MALFUNCTION FLAG - WORD 2 - Bit 7 - 22 0x80 KKMASK2: MALFUNCTION FLAG - WORD 2 - Bit 6 - 23 0x40 KKMASK2: MALFUNCTION FLAG - WORD 2 - Bit 5 - 24 0x20 KKMASK2: MALFUNCTION FLAG - WORD 2 - Bit 4 - 25 0x10 KKMASK2: MALFUNCTION FLAG - WORD 2 - Bit 3 - 26 0x08 KKMASK2: MALFUNCTION FLAG - WORD 2 - Bit 2 - 27 0x04 KKMASK2: MALFUNCTION FLAG - WORD 2 - Bit 1 - 28 0x02 KKMASK2: MALFUNCTION FLAG - WORD 2 - Bit 0 - 29 0x01 KKMASK3: MALFUNCTION FLAG - WORD 3 - Bit 7 - 31 0x80 KKMASK3: MALFUNCTION FLAG - WORD 3 - Bit 6 - 32 0x40 KKMASK3: MALFUNCTION FLAG - WORD 3 - Bit 5 - 33 0x20 KKMASK3: MALFUNCTION FLAG - WORD 3 - Bit 4 - 34 0x10 KKMASK3: MALFUNCTION FLAG - WORD 3 - Bit 3 - 35 0x08 KKMASK3: MALFUNCTION FLAG - WORD 3 - Bit 2 - 36 0x04 KKMASK3: MALFUNCTION FLAG - WORD 3 - Bit 1 - 37 0x02 KKMASK3: MALFUNCTION FLAG - WORD 3 - Bit 0 - 38 0x01 KKMASK4: MALFUNCTION FLAG - WORD 4 - Bit 7 - 39 0x80 KKMASK4: MALFUNCTION FLAG - WORD 4 - Bit 6 - 41 0x40 KKMASK4: MALFUNCTION FLAG - WORD 4 - Bit 5 - 42 0x20 KKMASK4: MALFUNCTION FLAG - WORD 4 - Bit 4 - 43 0x10 KKMASK4: MALFUNCTION FLAG - WORD 4 - Bit 3 - 44 0x08 KKMASK4: MALFUNCTION FLAG - WORD 4 - Bit 2 - 45 0x04 KKMASK4: MALFUNCTION FLAG - WORD 4 - Bit 1 - 46 0x02 KKMASK4: MALFUNCTION FLAG - WORD 4 - Bit 0 - 47 0x01 KKMASK5: MALFUNCTION FLAG - WORD 5 - Bit 7 - 48 0x80 KKMASK5: MALFUNCTION FLAG - WORD 5 - Bit 6 - 49 0x40 KKMASK5: MALFUNCTION FLAG - WORD 5 - Bit 5 - 51 0x20 KKMASK5: MALFUNCTION FLAG - WORD 5 - Bit 4 - 52 0x10 KKMASK5: MALFUNCTION FLAG - WORD 5 - Bit 3 - 53 0x08 KKMASK5: MALFUNCTION FLAG - WORD 5 - Bit 2 - 54 0x04 KKMASK5: MALFUNCTION FLAG - WORD 5 - Bit 1 - 55 0x02 KKMASK5: MALFUNCTION FLAG - WORD 5 - Bit 0 - 56 0x01 KKKMASK1: MALF FLAG - CHECK LAMP ENABLE WORD 1 - Bit 7 - 13 0x80 KKKMASK1: MALF FLAG - CHECK LAMP ENABLE WORD 1 - Bit 6 - 14 0x40 KKKMASK1: MALF FLAG - CHECK LAMP ENABLE WORD 1 - Bit 5 - 15 0x20 KKKMASK1: MALF FLAG - CHECK LAMP ENABLE WORD 1 - Bit 4 - 16 0x10 KKKMASK1: MALF FLAG - CHECK LAMP ENABLE WORD 1 - Bit 3 - 17 0x08 KKKMASK1: MALF FLAG - CHECK LAMP ENABLE WORD 1 - Bit 2 - 18 0x04 KKKMASK1: MALF FLAG - CHECK LAMP ENABLE WORD 1 - Bit 1 - 19 0x02 KKKMASK1: MALF FLAG - CHECK LAMP ENABLE WORD 1 - Bit 0 - 21 0x01 KKKMASK2: MALF FLAG - CHECK LAMP ENABLE WORD 2 - Bit 7 - 22 0x80 KKKMASK2: MALF FLAG - CHECK LAMP ENABLE WORD 2 - Bit 6 - 23 0x40 KKKMASK2: MALF FLAG - CHECK LAMP ENABLE WORD 2 - Bit 5 - 24 0x20 KKKMASK2: MALF FLAG - CHECK LAMP ENABLE WORD 2 - Bit 4 - 25 0x10 KKKMASK2: MALF FLAG - CHECK LAMP ENABLE WORD 2 - Bit 3 - 26 0x08 KKKMASK2: MALF FLAG - CHECK LAMP ENABLE WORD 2 - Bit 2 - 27 0x04 KKKMASK2: MALF FLAG - CHECK LAMP ENABLE WORD 2 - Bit 1 - 28 0x02 KKKMASK2: MALF FLAG - CHECK LAMP ENABLE WORD 2 - Bit 0 - 29 0x01 KKKMASK3: MALF FLAG - CHECK LAMP ENABLE WORD 3 - Bit 7 - 31 0x80 KKKMASK3: MALF FLAG - CHECK LAMP ENABLE WORD 3 - Bit 6 - 32 0x40 KKKMASK3: MALF FLAG - CHECK LAMP ENABLE WORD 3 - Bit 5 - 33 0x20 KKKMASK3: MALF FLAG - CHECK LAMP ENABLE WORD 3 - Bit 4 - 34 0x10 KKKMASK3: MALF FLAG - CHECK LAMP ENABLE WORD 3 - Bit 3 - 35 0x08 KKKMASK3: MALF FLAG - CHECK LAMP ENABLE WORD 3 - Bit 2 - 36 0x04 KKKMASK3: MALF FLAG - CHECK LAMP ENABLE WORD 3 - Bit 1 - 37 0x02 KKKMASK3: MALF FLAG - CHECK LAMP ENABLE WORD 3 - Bit 0 - 38 0x01 KKKMASK4: MALF FLAG - CHECK LAMP ENABLE WORD 4 - Bit 7 - 39 0x80 KKKMASK4: MALF FLAG - CHECK LAMP ENABLE WORD 4 - Bit 6 - 41 0x40 KKKMASK4: MALF FLAG - CHECK LAMP ENABLE WORD 4 - Bit 5 - 42 0x20 KKKMASK4: MALF FLAG - CHECK LAMP ENABLE WORD 4 - Bit 4 - 43 0x10 KKKMASK4: MALF FLAG - CHECK LAMP ENABLE WORD 4 - Bit 3 - 44 0x08 KKKMASK4: MALF FLAG - CHECK LAMP ENABLE WORD 4 - Bit 2 - 45 0x04 KKKMASK4: MALF FLAG - CHECK LAMP ENABLE WORD 4 - Bit 1 - 46 0x02 KKKMASK4: MALF FLAG - CHECK LAMP ENABLE WORD 4 - Bit 0 - 47 0x01 KKKMASK5: MALF FLAG - CHECK LAMP ENABLE WORD 5 - Bit 7 - 48 0x80 KKKMASK5: MALF FLAG - CHECK LAMP ENABLE WORD 5 - Bit 6 - 49 0x40 KKKMASK5: MALF FLAG - CHECK LAMP ENABLE WORD 5 - Bit 5 - 51 0x20 KKKMASK5: MALF FLAG - CHECK LAMP ENABLE WORD 5 - Bit 4 - 52 0x10 KKKMASK5: MALF FLAG - CHECK LAMP ENABLE WORD 5 - Bit 3 - 53 0x08 KKKMASK5: MALF FLAG - CHECK LAMP ENABLE WORD 5 - Bit 2 - 54 0x04 KKKMASK5: MALF FLAG - CHECK LAMP ENABLE WORD 5 - Bit 1 - 55 0x02 KKKMASK5: MALF FLAG - CHECK LAMP ENABLE WORD 5 - Bit 0 - 56 0x01 F78: TPS - TPS default value vs RPM 1 4 0 0 RPM 6 4 0 0 2 0.000000 255.000000 1 F1: IDLE: Idle Spark Advance as a function of MAP 1 4 0 0 kPa 11 4 0 0 2 0.000000 255.000000 1 FCRNKEST: Crank EST Table - Spark Advance vs RPM (not used) 1 4 0 0 RPM 17 4 0 0 2 0.000000 255.000000 1 F1 SAMAIN: Main Spark Advance vs MAP and RPM MAP 11 4 0 0 RPM 12 4 0 0 2 0.000000 255.000000 1 F2: Coolant Advance vs MAP and Temp (Subtract KCTBIAS from value) MAP 5 4 0 0 Coolant 12 4 0 0 2 0.000000 255.000000 1 F4: EGR Advance vs RPM and Vacuum kPa (Vac) 15 4 0 0 RPM 11 4 0 0 2 0.000000 255.000000 1 F6: ESC Attack rate(Deg/Ms) vs RPM 1 4 0 0 RPM 4 4 0 0 2 0.000000 255.000000 1 F7: ESC recovery rate (Deg/Sec) vs RPM 1 4 0 0 RPM 4 4 0 0 2 0.000000 255.000000 1 F44: Altitude Advance(Deg) vs Baro & Vacuum MAP 6 4 0 0 Baro 2 4 0 0 2 0.000000 255.000000 1 FBUMP1: Tip-In Bump spark Vs TPS & RPM (subtract KBMPBIAS) %TPS 17 4 0 0 RPM 8 4 0 0 2 0.000000 255.000000 1 FBUMPDEC: Tip-In Bump spark Decay Table - Decay rate Vs TPS Deg/s 1 4 0 0 %TPS 9 4 0 0 2 0.000000 255.000000 1 F27: Injector Bias vs ADINJ 1 4 0 0 Volts 8 4 0 0 2 0.000000 255.000000 1 F94: Injector bias add-on vs Injector pulse width Ms 1 4 0 0 Ms offset 17 4 0 0 2 0.000000 255.000000 1 F28: EGR Dilution as a function of RPM and Vacuum kPa (Vac) 15 4 0 0 RPM 11 4 0 0 2 0.000000 255.000000 1 FVE1: Volumetric Efficiency (VE) as a function of MAP and RPM (Low RPM) MAP 9 4 0 0 RPM 11 4 0 0 2 0.000000 255.000000 1 FVE2: Volumetric Efficiency (VE) as a function of MAP and RPM (High RPM) MAP 9 4 0 0 RPM 13 4 0 0 2 0.000000 255.000000 1 F31: Inverse Temperature term vs Charge Temperature term (50000/value) = Deg K 1 4 0 0 Degrees K 17 4 0 0 2 0.000000 255.000000 1 F33: Voltage compensation vs Battery voltage 1 4 0 0 Volts 8 4 0 0 2 0.000000 255.000000 1 F34: DE Coolant factor vs COOLDEGB 1 4 0 0 DegC 13 4 0 0 2 0.000000 255.000000 1 F36: AE Multiplier Vs Engine RPM Table 1 4 0 0 RPM 6 4 0 0 2 0.000000 255.000000 1 F37: AE Temperature factor vs COOLDEGB 1 4 0 0 DegC 13 4 0 0 2 0.000000 255.000000 1 F38: AEDP Decay factor(% ref period) Vs COOLDEGB 1 4 0 0 DegC 4 4 0 0 2 0.000000 255.000000 1 F38: DEMAP Decay factor(% ref period) Vs COOLDEGB 1 4 0 0 DegC 4 4 0 0 2 0.000000 255.000000 1 F40: AE Gain Vs Delta manifold fuel 1 4 0 0 Counts 6 4 0 0 2 0.000000 255.000000 1 F41: DE Gain Vs Delta manifold fuel 1 4 0 0 Counts 6 4 0 0 2 0.000000 255.000000 1 F51: Initial Run A/F Ratio Time-Out vs Coolant Temperature Ratio 1 4 0 0 Degrees C 15 4 0 0 2 0.000000 255.000000 1 F52: Run A/F Time-Out Interval Vs COOLDEG 1 4 0 0 Degrees C 15 4 0 0 2 0.000000 255.000000 1 F53: Initial Crank Base Pulse Width vs COOLDEGB - If KCFTM0 = 0 1 4 0 0 Deg C 13 4 0 0 2 0.000000 255.000000 1 F54: Initial Crank Base Pulse Width vs COOLDEGB - If KCFTM0 <> 0 1 4 0 0 Deg C 13 4 0 0 2 0.000000 255.000000 1 F56: Cold Engine A/F Ratio vs COOLDEG and MAP MAP 9 4 0 0 DegC 13 4 0 0 2 0.000000 255.000000 1 F57: Idle A/F Ratio vs Coolant Temperature 1 4 0 0 Deg C 7 4 0 0 2 0.000000 255.000000 1 F60: Air Fuel ratio vs RPM and MAP MAP 12 4 0 0 RPM 16 4 0 0 2 0.000000 255.000000 1 F61: Lean Cruise Air Fuel Delta Vs RPM and MAP MAP 9 4 0 0 RPM 16 4 0 0 2 0.000000 255.000000 1 F66: Injector delay Table (% of Ref period vs RPM & TPS) TPS% 9 4 0 0 RPM 8 4 0 0 2 0.000000 255.000000 1 F100: % Coolant contribution for calculating charge temp Vs RPM & MAP MAP 9 4 0 0 RPM 16 4 0 0 2 0.000000 255.000000 1 F10: IAC - Warmup IAC motor position offset Vs COOLDEGB 1 4 0 0 Deg C 13 4 0 0 2 0.000000 255.000000 1 F13D: IAC - Desired RPM in Drive Vs Battery voltage 1 4 0 0 Volts 3 4 0 0 2 0.000000 255.000000 1 F13P: IAC - Desired RPM in Park/Neutral Vs Battery voltage 1 4 0 0 Volts 3 4 0 0 2 0.000000 255.000000 1 F13M: IAC - Desired RPM for manual trans Vs Battery voltage 1 4 0 0 Volts 3 4 0 0 2 0.000000 255.000000 1 F14: IAC - IAC Warmup decay rate Vs COOLDEGB 1 4 0 0 Deg C 13 4 0 0 2 0.000000 255.000000 1 F15: IAC - Fast idle offset Vs COOLDEGB 1 4 0 0 Deg C 13 4 0 0 2 0.000000 255.000000 1 F16: IAC - Throttle crack offset Vs RPM 1 4 0 0 RPM 9 4 0 0 2 0.000000 255.000000 1 2nd UNKOWN Change IAC of some sort 28 to 51 for most with 28 & 1A to 46 & 2A for last 2 1 4 0 0 RPM 8 4 0 0 2 0.000000 255.000000 1 F59: Baro params - Baro Adjustment offset to MAP A/D reading vs RPM & TPS %Thrott Pos 6 4 0 0 RPM 3 4 0 0 2 0.000000 255.000000 1 F55: Shift light - RPM Threshold vs NTPSLD to turn on shift light 1 4 0 0 %TPS 5 4 0 0 2 0.000000 255.000000 1 F42C: TCC UNLOCK table TPS limit Vs Road speed 1 4 0 0 km/h 11 4 0 0 2 0.000000 255.000000 1 F43C: TCC Lock table TPS limit vs Road Speed 1 4 0 0 km/h 11 4 0 0 2 0.000000 255.000000 1