Double check the input/output wires on the corrector.
The red and black were transposed on mine - input was going to output.
Took me a while to find that one. The input is actually marked on the board.
Search found 86 matches
- Mon Aug 25, 2014 7:45 pm
- Forum: General Tuning Discussion
- Topic: Speedo Correctors
- Replies: 63
- Views: 55907
- Sat Aug 23, 2014 11:41 am
- Forum: General Tuning Discussion
- Topic: Speedo Correctors
- Replies: 63
- Views: 55907
Re: Speedo Correctors
You are right - the manual is pretty ordinary. Set the input jumper to 8V2 and the output to pull down and it will work fine with a reluctor Input driving an 808. How many pulses per rev does the T56 produce? If it is 40 like the reluctors in the auto's you will have to apply some serious correction...
- Fri Aug 22, 2014 6:52 pm
- Forum: General Tuning Discussion
- Topic: Speedo Correctors
- Replies: 63
- Views: 55907
Re: Speedo Correctors
No mods, just set the jumpers as per the instructions.
- Fri Aug 22, 2014 6:21 pm
- Forum: General Tuning Discussion
- Topic: Speedo Correctors
- Replies: 63
- Views: 55907
Re: Speedo Correctors
Hi Dylan,
Reluctor in and Hall out works fine.
Reluctor in and Hall out works fine.
- Fri Aug 22, 2014 4:19 pm
- Forum: General Tuning Discussion
- Topic: Speedo Correctors
- Replies: 63
- Views: 55907
Re: Speedo Correctors
Having played with this thing a bit, I have to say I am a little disappointed. Firstly, the input and output wires were reversed on the board. Took some head scratching to discover. Secondly, even when set to zero correction, if you slowly sweep the input frequency, the output is very 'notchy'. When...
- Wed Aug 20, 2014 6:53 pm
- Forum: General Tuning Discussion
- Topic: Speedo Correctors
- Replies: 63
- Views: 55907
Re: Speedo Correctors
The AC coupling link applies to the output.
Will try to bench test tonight and report back.
Will try to bench test tonight and report back.
- Wed Aug 20, 2014 4:20 pm
- Forum: General Tuning Discussion
- Topic: Speedo Correctors
- Replies: 63
- Views: 55907
Re: Speedo Correctors
I took one for the team and laid out $39.95 today.
Unit has 4 wires. 2 for DC supply, 1 input and 1 output, which may make VR inputs difficult to accommodate.
I have attached a scan of the users manual and a photo of the board.
The back of the board has a SMT PIC controller.
Unit has 4 wires. 2 for DC supply, 1 input and 1 output, which may make VR inputs difficult to accommodate.
I have attached a scan of the users manual and a photo of the board.
The back of the board has a SMT PIC controller.
- Tue Feb 04, 2014 7:34 am
- Forum: Delco ECU Conversions
- Topic: holden hz 350 overlander conversion
- Replies: 46
- Views: 34694
Re: holden hz 350 overlander conversion
Pretty common issue with retrofits into earlier Holden's. Loss of power to the ECU during cranking will sometimes cause a backfire as the key is released. Sometimes it will start when released. When you spin the distributor by hand, it leaves enough fuel in the manifold to allow it to fire when you ...
- Fri Sep 20, 2013 9:36 am
- Forum: Members Rides
- Topic: FC with VT 5L
- Replies: 136
- Views: 68387
Re: FC with VT 5L
How about a Torana bracket?
Low and close to the block on the drivers side.
Low and close to the block on the drivers side.
- Fri Sep 13, 2013 7:03 pm
- Forum: For Sale
- Topic: FS: VT, VX & VY BCM's & key to suit
- Replies: 29
- Views: 34421
Re: FS: VT, VX & VY BCM's & key to suit
Hi VX, do you have any of the VY 210's left? If so, how much are you chasing?
Cheers,
Matt
Cheers,
Matt