Search found 86 matches
- Wed Jul 29, 2009 8:57 am
- Forum: Hardware
- Topic: Electronics Australia DELCO articles
- Replies: 16
- Views: 12366
Re: Electronics Australia DELCO articles
I have repaired a couple over the years. Most common problem is dry joints causing intermitent operation. If you are desperate, the transistor of a VK EST module (also made by Bosch) works fine, and is not worth much on Ebay etc. Another source for the transistors are the Bosch modules that look lik...
- Thu Jul 23, 2009 2:18 pm
- Forum: Holden ALDL ECUs
- Topic: VT and vy V6 XDF
- Replies: 25
- Views: 19047
Re: VT and vy V6 XDF
Well put Justin,
Many of us have skills/information that we could charge for, however, there is always a lot more to learn, and the more information we throw into the pool, the better off we will all be.
I gain much greater satisfaction from helping out fellow enthusiasts.
Matt
Many of us have skills/information that we could charge for, however, there is always a lot more to learn, and the more information we throw into the pool, the better off we will all be.
I gain much greater satisfaction from helping out fellow enthusiasts.
Matt
- Fri Jul 10, 2009 4:54 pm
- Forum: Wiring
- Topic: JE Oil pressure switch - WHY ?
- Replies: 31
- Views: 23300
Re: JE Oil pressure switch - WHY ?
Yeah, the analog calibration for a 202 would be pretty rough.
- Fri Jul 10, 2009 11:02 am
- Forum: Wiring
- Topic: JE Oil pressure switch - WHY ?
- Replies: 31
- Views: 23300
Re: JE Oil pressure switch - WHY ?
The oil pressure switch is actually for backup fuel mode when the ECU is dead and not controlling outputs. The analog backup fuel controller can't drive the fuel pump relay so it relies on oil pressure to enable the pump. Cranking times will be longer in this mode while oil pressure builds. The O.P....
- Thu Jul 09, 2009 10:56 am
- Forum: Wiring
- Topic: Does anyone have a JE Camira Wiring Diagram ?
- Replies: 17
- Views: 20765
Re: Does anyone have a JE Camira Wiring Diagram ?
Another good source for Camira ignition modules and sensors are 90's Daewoo's. My local pick a part has dozens of them.
Harnesses from these things may be worth a look also. Basically a Camira engine, different ECU with similar pinout to an 808.
Harnesses from these things may be worth a look also. Basically a Camira engine, different ECU with similar pinout to an 808.
- Thu Jun 25, 2009 10:05 am
- Forum: Custom Code
- Topic: OSE $12P Teaser
- Replies: 91
- Views: 63677
Re: OSE $12P Teaser
Hey VL400,
How much different is the soft touch rev limiter to the standard limiter?
The basic limiter is that crude that conrods/bolts would probably be better off with a bit of an over rev. At least they would not be going through cycles of full power, no power, full power etc. at peek revs.
How much different is the soft touch rev limiter to the standard limiter?
The basic limiter is that crude that conrods/bolts would probably be better off with a bit of an over rev. At least they would not be going through cycles of full power, no power, full power etc. at peek revs.
- Fri Jun 19, 2009 8:40 am
- Forum: ALDL, OBDII Logging and Scanning
- Topic: Logging to an SD Card or SPI EEPROM Internally to the ECM
- Replies: 21
- Views: 17765
Re: Logging to an SD Card or SPI EEPROM Internally to the ECM
Now we have to find someone who knows a bit about $12 code (and it's variants)
- Thu Jun 18, 2009 8:40 pm
- Forum: ALDL, OBDII Logging and Scanning
- Topic: Logging to an SD Card or SPI EEPROM Internally to the ECM
- Replies: 21
- Views: 17765
Re: Logging to an SD Card or SPI EEPROM Internally to the ECM
Just had a thought. If we invert a PLCC socket over the MCU, we get easy access to all of the pins required for a Serial EEPROM conversion. The socket is a nice fit. 6 wires to the chip, cut the I/O trace on the main board. Job done. 128K logger for under 20 bucks! Would also be a nice solderless wa...
- Thu Jun 18, 2009 7:52 am
- Forum: ALDL, OBDII Logging and Scanning
- Topic: Logging to an SD Card or SPI EEPROM Internally to the ECM
- Replies: 21
- Views: 17765
Re: Logging to an SD Card or SPI EEPROM Internally to the ECM
As the only reference to these bits is the DDR register, we should be able to use one/both of the 2 pins configured as inputs safely. It is interresting that these 3 I/O bits are connected to the FMD, Quad drivers and a pin marked as "poweroff" on the PSU IC. I wonder if this was used for ...
- Wed Jun 17, 2009 10:05 am
- Forum: ALDL, OBDII Logging and Scanning
- Topic: Logging to an SD Card or SPI EEPROM Internally to the ECM
- Replies: 21
- Views: 17765
Re: Nintendo DS logger?
You are right again VL400. Most of my other 808's give external access to the unused I/O pins. I have a 25LC1024 SPI EEPROM on it's way. 128K bytes. 10 bytes at 10 samples per second = ~20 minutes worth of logging. 10 bytes should cover the basics. Would be nice to trim it down a bit to extend the l...