Search found 23 matches
- Fri Aug 06, 2021 9:40 am
- Forum: Holden ALDL ECUs
- Topic: false knock counts
- Replies: 11
- Views: 3236
Re: false knock counts
yes, im very happy with sam's tune it works very well for me its just this false knock count thing did not occur when first converted! Its happened later but i just cant work out what changes i have done that may have induced it!! The only obvious changes that i can remember is the quieter exhaust f...
- Thu Aug 05, 2021 5:53 pm
- Forum: Holden ALDL ECUs
- Topic: false knock counts
- Replies: 11
- Views: 3236
Re: false knock counts
thanks gareth,, my thoughts as well. although im bit uncomfortable about turning the KS off long term? This was with a new sensor, and then i tried a second hand one which looked good for a little while then threw the same knock count. I was also thinking maybe an aftermarket radio GPS may be causin...
- Tue Aug 03, 2021 1:26 pm
- Forum: Holden ALDL ECUs
- Topic: false knock counts
- Replies: 11
- Views: 3236
Re: false knock counts
an earlier log
- Tue Aug 03, 2021 10:57 am
- Forum: Holden ALDL ECUs
- Topic: false knock counts
- Replies: 11
- Views: 3236
false knock counts
hi brains trust, im having an issue with false KS counts. Im getting a constant ~200 count (tunerpro5) using the 808 ECU this leads to a constant 12 deg retard. There is not one component in the electrical side that has not been replaced over the past 12 months. Im thinking that im getting electrica...
- Tue Mar 30, 2021 5:33 pm
- Forum: Wanted
- Topic: MEMCAL reprogram VATS removal etc
- Replies: 2
- Views: 2463
Re: MEMCAL reprogram VATS removal etc
thanks i will
rgds
rgds
- Fri Mar 26, 2021 10:04 am
- Forum: Wanted
- Topic: MEMCAL reprogram VATS removal etc
- Replies: 2
- Views: 2463
MEMCAL reprogram VATS removal etc
Brains trust, help needed. I need a MEMCAL reprogrammed. VS V6, 9728 PCM Application: Conversion using ecotec motor but memcal needs to be changed to suit, Loom is from an VS auto but wiring to trans has just been cut at this stage VSS will be sent to the T5 pin on the PCM plugs (aftermarket vss gen...
- Sat Mar 13, 2021 10:01 am
- Forum: Holden ALDL ECUs
- Topic: 4L60 trans behind ecotec
- Replies: 6
- Views: 2341
Re: 4L60 trans behind ecotec
vx67
you suggest staying with the 808 ecu and loom then?
$11p or $12p 2 BAR MAP?
you suggest staying with the 808 ecu and loom then?
$11p or $12p 2 BAR MAP?
- Sat Mar 13, 2021 9:59 am
- Forum: Holden ALDL ECUs
- Topic: 4L60 trans behind ecotec
- Replies: 6
- Views: 2341
Re: 4L60 trans behind ecotec
jxx,
thats what i have done re the TCC runs through an on/off switch as well as the 4 gear switch in the trans.
thats what i have done re the TCC runs through an on/off switch as well as the 4 gear switch in the trans.
- Fri Mar 12, 2021 7:53 pm
- Forum: Holden ALDL ECUs
- Topic: 4L60 trans behind ecotec
- Replies: 6
- Views: 2341
4L60 trans behind ecotec
Hi, Information required please. I have a 4L60 trans behind an ecotec running on an 808 ecu with modded memcal. I am now thinking of going L67 but have to keep the 4L60 trans (hilux conversion, and recent H/D rebuild, output shaft is custom so changing trans is a no go) What do i need to do to run t...
- Sun Nov 08, 2020 6:47 pm
- Forum: Hardware
- Topic: DFI module
- Replies: 1
- Views: 2365
DFI module
Hi, im running a late VN loom in my hilux. all is good except when i recently changed out mf DFI for a new unit, Now my tacho is not working? plugged in old unit tacho works. suspecting the new DFI swapped it for another new bosch unit, Again no tacho. Wire for tacho is taken off the DFI plug and wo...