Search found 37 matches
- Thu Apr 05, 2018 9:39 pm
- Forum: Chip/Memcal Reading/Writing
- Topic: willem eprom write error
- Replies: 1
- Views: 3034
willem eprom write error
Trying to write a simple vats removal for BWFU0310 original file reads correct, change vats to disabled and recheck in hex to see 1 byte of data changed all seems good. write file to eprom and wont verify, check data written and missing bulk sections. using PCB50B board and willem eprom to read/writ...
- Sun Oct 15, 2017 10:36 pm
- Forum: Holden ALDL ECUs
- Topic: 808 comms and turner pro not working
- Replies: 11
- Views: 5761
Re: 808 comms and turner pro not working
So sorted the issue, had no chassis earth so all earths to ecu were 300ohm or above. Tensioned all pins in plugs but found dry solder joints in 2nd ecu so threw in the bin and went back to original ecu. Didn't bother with Comms board just tuned old Skool and got the job done
- Sun Oct 15, 2017 9:43 am
- Forum: Holden ALDL ECUs
- Topic: 808 comms and turner pro not working
- Replies: 11
- Views: 5761
Re: 808 comms and turner pro not working
Has anyone got a wiring diagram for the 9pin white plug and the diagnostic 6pin white plug that's near ecu, Don't have any of my diagrams with me and haven't done one of these in quite a while to remember.
- Sun Oct 15, 2017 9:37 am
- Forum: Holden ALDL ECUs
- Topic: 808 comms and turner pro not working
- Replies: 11
- Views: 5761
Re: 808 comms and turner pro not working
Comms board lights up, nvram board lights up. It's a conversion in an old statesman, they put on the dyno due to surging so has been like it since conversion done. No diagnostic light or plug, I'm going over wiring now and found most pins spread in ecu plugs. It cut out every now and then, found a w...
- Sat Oct 14, 2017 10:09 pm
- Forum: Holden ALDL ECUs
- Topic: 808 comms and turner pro not working
- Replies: 11
- Views: 5761
Re: 808 comms and turner pro not working
Yeah this is doing my head in! So I changed ecu's, ran a new patch wire for writing to ecu, wired the Comms board and still no Comms. Std eprom Eng warm running is 12.5afr idle any load at all runs 15.5afr and up if I kept applying load. The 12p file runs 11.8afr idle and 2500rpm wot afr start climb...
- Fri Oct 13, 2017 2:26 pm
- Forum: Holden ALDL ECUs
- Topic: 808 comms and turner pro not working
- Replies: 11
- Views: 5761
Re: 808 comms and turner pro not working
tried and no communication with flashtool trying a new ecu as this one is rich at idle and lean under load, no changes i make to ve table or af ratio table make a differance so possible ecu is faulty and in base fueling. I've upgraded the eprom to a 27c256 and loaded the OSE12P bin on that. See how ...
- Fri Oct 13, 2017 12:14 pm
- Forum: Holden ALDL ECUs
- Topic: 808 comms and turner pro not working
- Replies: 11
- Views: 5761
808 comms and turner pro not working
Hey Lads, so i have a 355 rebuilt stroker vp engine with an 808 ecu. I've soldered in the pcm comms board as per instructions and tested connections with a multimeter. I have the nvram installed, the ose12p v112 bin loaded and the oem memcal fitted to the nvram board and engine fires up no sweat i c...
- Sat Aug 12, 2017 12:16 pm
- Forum: Tools
- Topic: PCMHacking.net LS1 Flash Tool - comment thread
- Replies: 160
- Views: 133223
Re: PCMHacking.net LS1 Flash Tool - comment thread
Ahh ok, I'm after one that can write std files over tunerlocked ecu's
- Fri Aug 11, 2017 11:47 am
- Forum: Tools
- Topic: PCMHacking.net LS1 Flash Tool - comment thread
- Replies: 160
- Views: 133223
Re: PCMHacking.net LS1 Flash Tool - comment thread
What's the latest version and how do we purchase it.
- Tue Mar 21, 2017 8:26 am
- Forum: Chip/Memcal Reading/Writing
- Topic: Nvram jumper pins
- Replies: 9
- Views: 15757
Re: Nvram jumper pins
Hey Antus can you please pm me the info on the new nvrams I got both but no info with them
Thanks mate
Thanks mate