I just found this post - very late I know. You stated at the start that you were using 20psi fuel pressure. That seams very low as most EFI engines use approx 45psi (3Bar). Not sure if you ended up sorting it all out but low fuel pressure would give you lots of dramas.
Cheers
David
Search found 17 matches
- Sun May 15, 2022 5:20 pm
- Forum: Custom Code
- Topic: Calibrating a 4 cylinder engine
- Replies: 36
- Views: 37903
- Sun May 15, 2022 5:07 pm
- Forum: Holden ALDL ECUs
- Topic: VY PCM - 16269238
- Replies: 92
- Views: 84652
Re: VY PCM - 16269238
Thanks to everyone for your input. Tuning now works fine after help by Envyous Customs - Legend.
- Sun Jan 16, 2022 5:37 pm
- Forum: Holden ALDL ECUs
- Topic: VY PCM - 16269238
- Replies: 92
- Views: 84652
Re: VY PCM - 16269238
Yeh. I have been dicking around with this for nearly two weeks now. Even bought the second PCM to help with diagnosing. Thanks for helping out. I will contact Envyous Customs and see if they can help - bought the ALDL cable last year but this is the first chance I have had to use it. Cheers again fo...
- Sun Jan 16, 2022 3:41 pm
- Forum: Holden ALDL ECUs
- Topic: VY PCM - 16269238
- Replies: 92
- Views: 84652
Re: VY PCM - 16269238
Hi again, this is one of the instruction lists that I have been following. Bench Wiring/Programming VX and VY Holden V6 PCM PCM Grounds: *All these grounds are tied together in the engine harness 300mm from the PCM connectors. *A05 = Black/Red *B05 = Black/Red *E07 = Black/Red *F07 = Black/Red ……………...
- Sun Jan 16, 2022 12:17 pm
- Forum: Holden ALDL ECUs
- Topic: VY PCM - 16269238
- Replies: 92
- Views: 84652
Re: VY PCM - 16269238
Hi and thanks for replying. I have followed the instructions from this web site. PCM Diagnostic: This wire is connected to Pin 6 of the ALDL connector. It is a signal to the PCM to activate Diagnostic Mode. D09 = White/ Black Pin 5 of the ALDL connector Black/ Yellow wire is connected to Bat- Neg. T...
- Sat Jan 15, 2022 1:47 pm
- Forum: Holden ALDL ECUs
- Topic: VY PCM - 16269238
- Replies: 92
- Views: 84652
Re: VY PCM - 16269238
Hi there, I'm hoping someone can help me. I have carried out an engine conversion on a 2003 Ford Transit using a 2003 Holden Commodore VY V6 Ecotec engine and 4L60E auto transmission. The loom was modified by The Castlemaine Rod Shop to work without the BCM and ignition key. I purchased the USB ALDL...
- Sat Aug 07, 2021 5:54 am
- Forum: Wiring
- Topic: Ecotec conversion to a 1928 Ford street rod project
- Replies: 12
- Views: 10330
Re: Ecotec conversion to a 1928 Ford street rod project
Your Rod is looking good Peter. I feel your pain as it took me 4 years to get my 1972 Beetle on the road and then I have spent the last 10 years modifying and changing stuff. But it keeps us a home where the missus can find us. The dash is looking neat, nice and simple and I see the changes you have...
- Fri Aug 06, 2021 5:41 pm
- Forum: Wanted
- Topic: VR Engine Loom
- Replies: 2
- Views: 2503
Re: VR Engine Loom
Thanks for that info. Might help me locate a suitable loom.
Cheers
Cheers
- Thu Aug 05, 2021 2:20 pm
- Forum: Wiring
- Topic: Ecotec conversion to a 1928 Ford street rod project
- Replies: 12
- Views: 10330
Re: Ecotec conversion to a 1928 Ford street rod project
Hi 28Ford, Wondering how your project was going? I am still working on that Transit van conversion. Loom is getting modified by Castlemaine Rod Shop. Crossmember and engine are ready to go in. Then the fun starts with connecting everything up, e.g. radiator, tailshaft, fuel system, tacho, speedo, ex...
- Thu Aug 05, 2021 2:13 pm
- Forum: Wanted
- Topic: VR Engine Loom
- Replies: 2
- Views: 2503
VR Engine Loom
Hi there, chasing a VR engine loom so I can practice programing a VR ECM. So it will be used for bench testing to start with and then later on, if all goes well, I will convert the loom to run a turbocharged 1915cc VW Superbug. Also after the ECM plugs to suit the VY computer. That engine is going i...