Search found 13 matches
- Sun Jan 13, 2019 7:53 pm
- Forum: Hardware Modification and Development
- Topic: Coil negative signal conditioning
- Replies: 10
- Views: 14790
Re: Coil negative signal conditioning
Got the diodes, made circuit board up. Testing on car tomoz.
- Sat Jan 12, 2019 8:56 pm
- Forum: Hardware Modification and Development
- Topic: Coil negative signal conditioning
- Replies: 10
- Views: 14790
Re: Coil negative signal conditioning
Any luck with getting your circuit going? I still waiting on Jaycar to get zeners in stock
- Sat Dec 15, 2018 7:44 pm
- Forum: Hardware Modification and Development
- Topic: Coil negative signal conditioning
- Replies: 10
- Views: 14790
Re: Coil negative signal conditioning
I spoke with my sparky mate and we both come up with;
Coil -ve -------> 100K resistor ------> 5v Zener diode ---------> to PCM
will be testing once i get the materials, using a VS PCM (16176424) with 4L60e standalone.
Coil -ve -------> 100K resistor ------> 5v Zener diode ---------> to PCM
will be testing once i get the materials, using a VS PCM (16176424) with 4L60e standalone.
- Sat Dec 08, 2018 7:46 pm
- Forum: Holden ALDL ECUs
- Topic: 16176424 Standalone for 4L60e
- Replies: 18
- Views: 7780
Re: 16176424 Standalone for 4L60e
Another option be an Arduino board?
I could use a hall effect pickup which will ensure 5v continous power via a regular 12v to 5v.
Then ill machine a magentic pickup and attach it to the crank pulley.
Could then use this for multiple engine applications.
I could use a hall effect pickup which will ensure 5v continous power via a regular 12v to 5v.
Then ill machine a magentic pickup and attach it to the crank pulley.
Could then use this for multiple engine applications.
- Thu Dec 06, 2018 9:36 pm
- Forum: Holden ALDL ECUs
- Topic: 16176424 Standalone for 4L60e
- Replies: 18
- Views: 7780
Re: 16176424 Standalone for 4L60e
Cheers mate,
Yes forgot to mention using a jaycar 12v to 5v converter which should be okay?
Regards Equada
Yes forgot to mention using a jaycar 12v to 5v converter which should be okay?
Regards Equada
- Thu Dec 06, 2018 8:00 pm
- Forum: Holden ALDL ECUs
- Topic: 16176424 Standalone for 4L60e
- Replies: 18
- Views: 7780
Re: 16176424 Standalone for 4L60e
Hi guys, bit further down the road now. Got the engine running with carb conversion - Holley 600 Elec choke - MSD coil - Bypass regulator and stand alone pump relay via oil pressure - Proflow HEI distributor On PCM i hook up - TPS - CTS - VSS - 4L60e plugs Now need to figure what pinout is tach in r...
- Mon Jul 09, 2018 10:57 pm
- Forum: Holden ALDL ECUs
- Topic: 16176424 Standalone for 4L60e
- Replies: 18
- Views: 7780
Re: 16176424 Standalone for 4L60e
Evening guys cheers for the input, The speedo setup I am using is a vl speedo cable into a cableX to keep the original cluster. I also hate the 4l60e because of this. After much reading over the posts i will put back on the EFI manifold and TB and run the $11P VP104 base tune and go from there. Chee...
- Sat Jul 07, 2018 12:20 pm
- Forum: Holden ALDL ECUs
- Topic: 16176424 Standalone for 4L60e
- Replies: 18
- Views: 7780
Re: 16176424 Standalone for 4L60e
Cheers guys,
So i can just tune the memcal for curves when adjusting carb jets and their corresponding shift points.
What will happen if i don have the ignition modules hooked up as well as dizzy?
So i can just tune the memcal for curves when adjusting carb jets and their corresponding shift points.
What will happen if i don have the ignition modules hooked up as well as dizzy?
- Fri Jul 06, 2018 7:14 pm
- Forum: Holden ALDL ECUs
- Topic: 16176424 Standalone for 4L60e
- Replies: 18
- Views: 7780
Re: 16176424 Standalone for 4L60e
Cheers Delcowizzid,
By leaving everything else connected i would run a t-piece for IAC and MAP.
My assumption is that the EFI curves would wreak havoc for carb tuning?
By leaving everything else connected i would run a t-piece for IAC and MAP.
My assumption is that the EFI curves would wreak havoc for carb tuning?
- Fri Jul 06, 2018 1:01 pm
- Forum: Holden ALDL ECUs
- Topic: 16176424 Standalone for 4L60e
- Replies: 18
- Views: 7780
Re: 16176424 Standalone for 4L60e
Cheers for the replies,
Its a carby fed 304 with 4l60e in a VL.
My scope of the query is to see if it can be done just for a cruising car.
Its a carby fed 304 with 4l60e in a VL.
My scope of the query is to see if it can be done just for a cruising car.