Search found 7653 matches
- Fri Mar 22, 2024 1:12 pm
- Forum: Members Rides
- Topic: Torana SS
- Replies: 262
- Views: 195961
Re: Torana SS
I guess it's what ever your used to and prefer. I like light pedal personally. I've realized that I dislike modern brakes, from the operator side of things, not the actual stopping power. To me, I can't stand the delay of the modern car's brake pedal to go down to the point the brakes start working,...
- Thu Mar 21, 2024 7:24 pm
- Forum: Realtime Delco Tuning
- Topic: Cold and hot idle setting strategy ?
- Replies: 22
- Views: 5096
Re: Cold and hot idle setting strategy ?
That's a decent enough cam, would need some 35-40 lb injectors, L67 ones should be enough but no harm going bigger. With the idle screw, it needs to be set so the IAC steps in TP once fully warmed up and settled to be about 20 steps. Using the screw to adjust the idle is a no no as the ECU will try ...
- Thu Mar 21, 2024 4:08 pm
- Forum: Realtime Delco Tuning
- Topic: Cold and hot idle setting strategy ?
- Replies: 22
- Views: 5096
Re: Cold and hot idle setting strategy ?
Yeah, that's the stock late VP and VR injectors, 11p/12p stock data is for those as well as the 917s from earlier cars. So that should be all good then. What are the cam specs? The stock injectors would be borderline big enough for anything more than the basic baby/"stage 1" upgrades, espe...
- Thu Mar 21, 2024 12:09 pm
- Forum: Realtime Delco Tuning
- Topic: Cold and hot idle setting strategy ?
- Replies: 22
- Views: 5096
Re: Cold and hot idle setting strategy ?
Whats the PN on them and colour of the tops?
- Thu Mar 21, 2024 9:20 am
- Forum: Realtime Delco Tuning
- Topic: Cold and hot idle setting strategy ?
- Replies: 22
- Views: 5096
Re: Cold and hot idle setting strategy ?
I have not much problems leaving the setting stock, but a bigger cam with lots of overlap likes lean and will abruptly stall if too rich at cold and during warm up. Bigger cams also like heaps more timing at idle and light loads. You can just adjust the idle table and overlapping main table spark ce...
- Sun Mar 17, 2024 11:50 am
- Forum: Realtime Delco Tuning
- Topic: DTC for trans
- Replies: 9
- Views: 1475
Re: DTC for trans
Yes, that def would be the reason. If it's not lock up, the ECU will be cracking the shits for sure.
- Sun Mar 17, 2024 11:23 am
- Forum: Holden ALDL ECUs
- Topic: ose_$11p
- Replies: 26
- Views: 3090
Re: ose_$11p
My understanding is rpm range is primarily dictated by CPU resources and clock speed fighting the ever decreasing window of time available to execute instructions as the rpm increases. Table size of a few rows would only be a few bytes I'd imagine?
- Sun Mar 17, 2024 8:33 am
- Forum: Holden ALDL ECUs
- Topic: ose_$11p
- Replies: 26
- Views: 3090
Re: ose_$11p
Is this a processing limitation because the code has a lot more stuff to executed in 11P compared to 12P? I assumed 424 and 808 have essentially the same CPU?
- Sun Mar 17, 2024 8:26 am
- Forum: Realtime Delco Tuning
- Topic: DTC for trans
- Replies: 9
- Views: 1475
Re: DTC for trans
I suppose you could but I'd expect that it will continue to get worse with time and need readjusting to compensate. As for my bothers ute, I am sure it went into trans limp mode when that happened and was forced into 3rd. So I just turned off the DTC processing code flag and it drives fine as far as...
- Sat Mar 16, 2024 8:25 pm
- Forum: Holden ALDL ECUs
- Topic: ose_$11p
- Replies: 26
- Views: 3090
Re: ose_$11p
Can't use 12p instead and run 808? They go to 9.6k standard.