Search found 7305 matches
- Mon Apr 01, 2024 8:01 am
- Forum: Holden ALDL ECUs
- Topic: 424 input
- Replies: 9
- Views: 1391
Re: 424 input
There are unused inputs, look at the pin listing in the 11p zip and look for inputs without a blank description and in the overview pdf, and the description of the fields in the log definition (adx) for ones which list the pin but not purpose. Note the coltage range. Knock is special, you cant use i...
- Sat Mar 30, 2024 7:51 am
- Forum: GM LS1 512Kbyte and 1Mbyte and newer
- Topic: P10 Tuning
- Replies: 28
- Views: 7311
Re: P10 Tuning
Thanks, but as above we need another developer with interest in adding slave support to go further. Its a hard one, because the code is stored in the cpu and we need to understand and create the mechenism of running code on the slave and using shared memory to get the payload in to the slave's stora...
- Fri Mar 29, 2024 9:34 pm
- Forum: GM LS1 512Kbyte and 1Mbyte and newer
- Topic: P10 Tuning
- Replies: 28
- Views: 7311
Re: P10 Tuning
No. Mine arrived but appears to be dead on arrival, and there has not been much interest in it, or few posts about it. As above you can tune the calibration in a bin, but at this stage pcmhammer support for the slave cpu is unlikely to be developed without another developer coming aboard who wants t...
- Fri Mar 29, 2024 11:36 am
- Forum: GM LS1 512Kbyte and 1Mbyte and newer
- Topic: Cables That DO NOT Work With PCM Hammer
- Replies: 2
- Views: 2227
Re: Cables That DO NOT Work With PCM Hammer
Exactly right. Regarding the tactrix, its not so much pcmhammer doesnt support the tool, its that the tool doesnkt support the pcm's vpw protocol. Regarding the mongoose, I read there are clones of the JLT out there, its not clear if this is a bad clone or a problem with the JLT not supporting vpw. ...
- Sun Mar 24, 2024 9:12 pm
- Forum: ALDL, OBDII Logging and Scanning
- Topic: New engine, first start up tune ?
- Replies: 22
- Views: 5835
Re: New engine, first start up tune ?
eventually, yes. 8-10 years is a long time. Its such a pitty electronics shops that do this sort of stuff are so rare now.
- Sun Mar 24, 2024 11:23 am
- Forum: General Tuning Discussion
- Topic: Tuning Order
- Replies: 1
- Views: 2184
Re: Tuning Order
You probably want to get idle in the ballpark first so you can sit there in the car looking at your laptop without it stalling. How you get the idle in might depend on calibrating any hardware you change, MAF, injectors, etc rather than idle tables. Then I'd do AFR, if the spark seemed sain and not ...
- Sun Mar 24, 2024 11:12 am
- Forum: ALDL, OBDII Logging and Scanning
- Topic: New engine, first start up tune ?
- Replies: 22
- Views: 5835
Re: New engine, first start up tune ?
If it's a '424 and you are putting 11P on the standard memcal it'll fit. But they're very old and they don't have electronic erase. So you need to get a UV eraser and pull the sticker off the chip and erase it with UV light. Most people replace the chip with an electronic erase version, and make up ...
- Sat Mar 23, 2024 11:02 am
- Forum: ALDL, OBDII Logging and Scanning
- Topic: New engine, first start up tune ?
- Replies: 22
- Views: 5835
Re: New engine, first start up tune ?
You pull the nvram off the assembly and put it direct in the programmer. use a small flathead screw driver and lift it up a little at one end, then the other, then back to the first and so on and be careful not to bend the opposite corner leg when it comes off. when re-installing go gentle and make ...
- Fri Mar 22, 2024 9:25 pm
- Forum: Hardware Modification and Development
- Topic: Trigger Wheel Decoder / Coil driver
- Replies: 24
- Views: 11421
Re: Trigger Wheel Decoder / Coil driver
Cool, thanks
- Thu Mar 21, 2024 6:39 pm
- Forum: Engineering and Reverse Engineering
- Topic: E38 Sub Application Question
- Replies: 10
- Views: 4843
Re: E38 Sub Application Question
Maybe. There are people that run both computers from both generations in parallel, so consider that might be the case too.