There's approx 7.5mmHg per kPa
so 1" Hg is 25.4/7.5 = 3.386kPa
20"Hg is then 101.3kPa - (20 * 3.386) = ~ 33.6kPa Absolute
Search found 500 matches
- Fri Sep 16, 2022 9:55 am
- Forum: Engine/Transmision Mechanical
- Topic: Testing MAP sensor with vac gauge - due to rough idle
- Replies: 34
- Views: 13042
- Mon Sep 05, 2022 10:32 am
- Forum: Engineering and Reverse Engineering
- Topic: E92 PCM Reverse Engineering
- Replies: 278
- Views: 74069
Re: E92 PCM Reverse Engineering
Been a while since I looked at CAN, but is it using the extended frame format with the 29bit identifier?
- Mon Sep 05, 2022 10:27 am
- Forum: GM LS1 512Kbyte and 1Mbyte and newer
- Topic: PCM Hammer Release 021
- Replies: 345
- Views: 166829
Re: PCM Hammer Release 021
I wonder if it is related to the typo "PemHacking.OBDXProDevice" ?
- Tue Aug 30, 2022 11:11 am
- Forum: Wanted
- Topic: Wanted Dallas DS1245Y Replacement chip.
- Replies: 3
- Views: 3928
Re: Wanted Dallas DS1245Y Replacement chip.
Genuine and in stock: https://www.digikey.com.au/en/products/detail/analog-devices-inc-maxim-integrated/DS1245Y-70IND/1087328 https://au.mouser.com/ProductDetail/Maxim-Integrated/DS1245Y-70IND%2B?qs=0Y9aZN%252BMVCUV06j09H40sQ%3D%3D Digi-Key is slightly more expensive but you get free shipping over $...
- Sun Aug 28, 2022 4:34 pm
- Forum: General Tuning Discussion
- Topic: Cant connect to nvram
- Replies: 4
- Views: 2042
Re: Cant connect to nvram
So it wouldn't start with the original memcal?
Did you disconnect the battery while you swapped the nvram & memcal?
Did you disconnect the battery while you swapped the nvram & memcal?
- Mon Aug 22, 2022 7:34 am
- Forum: Holden ALDL ECUs
- Topic: VT SUPER6 - No 3x or 18x signal but cannot see fault codes?
- Replies: 14
- Views: 3752
Re: VT SUPER6 - No 3x or 18x signal but cannot see fault cod
The CAM sensor is only used by the PCM for sequential fuelling, the DIS models doesn't really care about it at all.
- Sun Aug 21, 2022 11:36 pm
- Forum: Custom Code
- Topic: VS-VY Enhanced Factory Bins
- Replies: 836
- Views: 758070
Re: The1's Enhanced Factory Bins
What would you suggest to be the best fit for a 95 v6 sfi rwd auto trans? This code is specifically for the Holden 5l V8 and 3.8l 90° V6 motors, with a P6 type PCM. We have real time support on the earlier models that were fitted with a memcal, but not on the later models with flash memory. Real ti...
- Sun Aug 21, 2022 10:29 pm
- Forum: Members Rides
- Topic: FX Holden Race Car Project
- Replies: 1397
- Views: 574146
Re: FX Holden Race Car Project
Gear pump is positive displacement, so should be pretty easy to figure out the approximate flow rate at any given speed. If the pressure is low either not enough oil going into the pump, or the downstream restriction is too low. As far as downstream restriction goes you could have a faulty relief va...
- Sun Aug 21, 2022 9:50 pm
- Forum: Holden ALDL ECUs
- Topic: VT SUPER6 - No 3x or 18x signal but cannot see fault codes?
- Replies: 14
- Views: 3752
Re: VT SUPER6 - No 3x or 18x signal but cannot see fault cod
The DIS module doesn't need the PCM at all to run the spark when it is in bypass mode (by default).
The PCM brings the DIS module out of bypass mode above 400 rpm and takes control once things are running.
The PCM brings the DIS module out of bypass mode above 400 rpm and takes control once things are running.
- Sat Aug 20, 2022 11:12 am
- Forum: Holden ALDL ECUs
- Topic: VT SUPER6 - No 3x or 18x signal but cannot see fault codes?
- Replies: 14
- Views: 3752
Re: VT SUPER6 - No 3x or 18x signal but cannot see fault cod
Also there are no other means of communications, aldl bus is it.