Setting up Wideband Datalogging Input Video

160 And 8192 Baud Aldl
User avatar
The1
Posts: 4694
Joined: Mon Jan 04, 2010 10:23 am

Setting up Wideband Datalogging Input Video

Post by The1 »

Here's me again with my dumb voice, hope you guys enjoy and get something usefull from it. Arh it's late im off.

[youtube]https://www.youtube.com/watch?v=58svlSl6Duo[/youtube]
tav
Posts: 38
Joined: Mon Oct 25, 2010 6:53 pm
cars: VS Commodore

Re: Setting up Wideband Datalogging Input Video

Post by tav »

Nice one :D
Dazza92VP
Posts: 607
Joined: Sun Jun 06, 2010 9:59 am
cars: 92 VP V8 Wagon
Location: Perth

Re: Setting up Wideband Datalogging Input Video

Post by Dazza92VP »

I thought vlad was volunteering for the next how to vid :D nice work anyway mate :thumbup:
User avatar
vlad01
Posts: 7780
Joined: Mon Oct 08, 2012 6:41 pm
cars: VP I S
VP I executive
VP II executive
VP II executive #2
VR II executive
Location: Kyneton, Vic

Re: Setting up Wideband Datalogging Input Video

Post by vlad01 »

Dazza92VP wrote:I thought vlad was volunteering for the next how to vid :D nice work anyway mate :thumbup:

:shh:
I'm the director of VSH (Vlad's Spec Holden), because HSV were doing it ass about.
User avatar
VL400
Posts: 4991
Joined: Sun Mar 01, 2009 2:54 pm
cars: VL Calais and Toyota Landcruiser. Plus some toys :)
Location: Perth, WA
Contact:

Re: Setting up Wideband Datalogging Input Video

Post by VL400 »

Good video mate :thumbup:


On a side note for those with 11P or 12P you do not need to change the ADX calc, its always left as X/10. There are two scalars you set to match the 0V and 5V AFR points (ie 0V=11AFR and 5V=17AFR if the wideband analog output is setup as discussed in this video), everything else is handled behind the scenes for you.
Dylan
Posts: 3355
Joined: Mon Aug 02, 2010 6:35 pm
cars: VR Commodore V8

Re: Setting up Wideband Datalogging Input Video

Post by Dylan »

11P is available to the public now??
User avatar
Holden202T
Posts: 10311
Joined: Sat Feb 28, 2009 9:05 pm
Location: Tenambit, NSW
Contact:

Re: Setting up Wideband Datalogging Input Video

Post by Holden202T »

I think what he is referring to is that's how its setup in both, when its available that is :)
User avatar
vlad01
Posts: 7780
Joined: Mon Oct 08, 2012 6:41 pm
cars: VP I S
VP I executive
VP II executive
VP II executive #2
VR II executive
Location: Kyneton, Vic

Re: Setting up Wideband Datalogging Input Video

Post by vlad01 »

question about the spartan WB, they state their output is 10AFR @ 0V and 20AFR @ 5V.

I put in those values in 12P, if the sensor is just running in the open air, should it peg out to 20AFR? cos it pegs out to 18.7AFR.

If I saturate the sensor with propane gas, its drops to min of 10AFR which is what I expect.
I'm the director of VSH (Vlad's Spec Holden), because HSV were doing it ass about.
User avatar
Jayme
Posts: 2585
Joined: Sun Mar 01, 2009 8:59 am
Location: North Coast, NSW

Re: Setting up Wideband Datalogging Input Video

Post by Jayme »

put a multi meter on the wideband output... does it get to 5V in open air?

I would suspect a bad earth on wideband maybe and hte ecu is not seeing the full 5v from the wideband.
Dylan
Posts: 3355
Joined: Mon Aug 02, 2010 6:35 pm
cars: VR Commodore V8

Re: Setting up Wideband Datalogging Input Video

Post by Dylan »

My 14.7 kit does the same. Cant remember the reading but around that.
Im about to put the narrow band back in so see how if compares. As I have nothing to check my readings in tuner pro against.
Post Reply