ALDL ECU's
Re: ALDL ECU's
Coulld this update help with reading the engine data?
Re: ALDL ECU's
Yep, I fixed that just before! I had a little mistake which missed out on the VS S3 V8's!Dylan wrote:Coulld this update help with reading the engine data?
Just sorting out this graphing stuff first then Ill upload the newest version.
Your Local Aussie Reverse Engineer
Contact for Software/Hardware development and Reverse Engineering
Site:https://www.envyouscustoms.com
Mob:+61406 140 726
Contact for Software/Hardware development and Reverse Engineering
Site:https://www.envyouscustoms.com
Mob:+61406 140 726
Re: ALDL ECU's
Cool can't wait to test it
Re: ALDL ECU's
There we go. All fixed!
- NewGraphing.PNG (28.74 KiB) Viewed 6552 times
Your Local Aussie Reverse Engineer
Contact for Software/Hardware development and Reverse Engineering
Site:https://www.envyouscustoms.com
Mob:+61406 140 726
Contact for Software/Hardware development and Reverse Engineering
Site:https://www.envyouscustoms.com
Mob:+61406 140 726
Re: ALDL ECU's
v0.0.0.4 Now available!
Changes include:
- adding 2more parameters to the graph.
- Fixed issue with VS S3 V8 (Engine data read and fault data)
- Error catches
- Reading is on separate thread to processing
Changes include:
- adding 2more parameters to the graph.
- Fixed issue with VS S3 V8 (Engine data read and fault data)
- Error catches
- Reading is on separate thread to processing
- Attachments
-
- AEDInstaller.exe
- (1.03 MiB) Downloaded 316 times
Your Local Aussie Reverse Engineer
Contact for Software/Hardware development and Reverse Engineering
Site:https://www.envyouscustoms.com
Mob:+61406 140 726
Contact for Software/Hardware development and Reverse Engineering
Site:https://www.envyouscustoms.com
Mob:+61406 140 726
Re: ALDL ECU's
The only thing left to do now, is add a little checkbox for "disable chatter" for the engine data reads. Hopefully thatll give a massive boost to the frames/s when needed.
And also an option to only record engine or transmission information
I dont mind it being a bit slower while cruising around, but be good to have the option available.
And also an option to only record engine or transmission information
I dont mind it being a bit slower while cruising around, but be good to have the option available.
Your Local Aussie Reverse Engineer
Contact for Software/Hardware development and Reverse Engineering
Site:https://www.envyouscustoms.com
Mob:+61406 140 726
Contact for Software/Hardware development and Reverse Engineering
Site:https://www.envyouscustoms.com
Mob:+61406 140 726
Re: ALDL ECU's
Is it possible for the ALDL based ECU's to be put into diagnostic mode electronically?
Would be great feature on some software to have a button to do that.
Would be great feature on some software to have a button to do that.
-
VL400
- Posts: 4991
- Joined: Sun Mar 01, 2009 2:54 pm
- cars: VL Calais and Toyota Landcruiser. Plus some toys :)
- Location: Perth, WA
- Contact:
Re: ALDL ECU's
Cant request diagnostic mode using the mode 4 commands (mode 4 tells the ECU to do certain things), but if its to set the timing you can use mode 4 to command any timing value you want - so can set a value that matches with a notch on the timing cover and set the timing to line up.
Re: ALDL ECU's
Not sure Im following on that?
Three new buttons will be add:
1- Disable vehicle comms to enhance frame/s (This is what Tunerpro does).
2- Log only Engine data
3- Log on Transmission data
I just got to add in some checks to the display updates and replay updates to check whether there is any data for trans/engine to process for each gauge.
Also finally. Iv had 1 report that the latest graphing causes a little error to occur after logging for a while and trying to "hover" over the points when "rolling data" has not been ticked. Iv actually recreated this error and I can semi repair this.
From now on, data points cannot be checked by hovering over unless logging has stopped, or the replay data has been paused/stopped.
Oh, and the entire window can now be expanded! I find this good for the graphing as it makes it large to check out!
New version out soon!
Three new buttons will be add:
1- Disable vehicle comms to enhance frame/s (This is what Tunerpro does).
2- Log only Engine data
3- Log on Transmission data
I just got to add in some checks to the display updates and replay updates to check whether there is any data for trans/engine to process for each gauge.
Also finally. Iv had 1 report that the latest graphing causes a little error to occur after logging for a while and trying to "hover" over the points when "rolling data" has not been ticked. Iv actually recreated this error and I can semi repair this.
From now on, data points cannot be checked by hovering over unless logging has stopped, or the replay data has been paused/stopped.
Oh, and the entire window can now be expanded! I find this good for the graphing as it makes it large to check out!
New version out soon!
Your Local Aussie Reverse Engineer
Contact for Software/Hardware development and Reverse Engineering
Site:https://www.envyouscustoms.com
Mob:+61406 140 726
Contact for Software/Hardware development and Reverse Engineering
Site:https://www.envyouscustoms.com
Mob:+61406 140 726
-
yoda69
- Posts: 1215
- Joined: Sun Mar 15, 2009 10:20 am
- cars: 2004 VYII Acclaim Wagon V6 Auto LPG/Petrol
2004 VYII Berlina sedan V6 Auto
2005 VZ Monaro CV8 manual - Location: Geelong, VIC
Re: ALDL ECU's
Nice work, had my first play tonight on my VY and looks good.
