Convert V6 Netres To V8
Re: Convert V6 Netres To V8
Hi all,
I'm doing a delco conversion on a chrysler 318 but I am unsure what I need to do in regard to the netres. The Memcal's I have are out of 4 & 6 cylider The EFI setup im using is TBI does this effect any of the resistance value's? or do I just need to cut the pin to change it to V8. Does the netres set the no. of cyl I notice the $5D xdf has this setting but the $12ose xdf (what I plan to use) does'nt. any help or links to info would be greatly appreciated.
I'm doing a delco conversion on a chrysler 318 but I am unsure what I need to do in regard to the netres. The Memcal's I have are out of 4 & 6 cylider The EFI setup im using is TBI does this effect any of the resistance value's? or do I just need to cut the pin to change it to V8. Does the netres set the no. of cyl I notice the $5D xdf has this setting but the $12ose xdf (what I plan to use) does'nt. any help or links to info would be greatly appreciated.
- delcowizzid
-
- Posts: 5356
- Joined: Sat Feb 28, 2009 8:38 pm
- Location: Wellington NZ
Re: Convert V6 Netres To V8
im not too sure actually about the TBI injection side of it i presume a V6 memcal with the pin cut should be fine as for bins to use i know vl400 has another one coming soon with 4 6 and 8 cylinder support in the one bin as to weather it has TBI support like the early bins thats a question for him to answer
will most likely depend on how many injectors are in the TBI unit im sure with a simple fudge of the injector constant youll be fine to run it no matter what

If Its Got Gas Or Ass Count Me In.if it cant be fixed with a hammer you have an electrical problem
Re: Convert V6 Netres To V8
So from What I understand,
I can just get away with cutting the 15k leg?
Not needing to add a 7.5k resistor or a solid jumper anywhere?
cheers
MaT
I can just get away with cutting the 15k leg?
Not needing to add a 7.5k resistor or a solid jumper anywhere?
cheers
MaT
Re: Convert V6 Netres To V8
Is there anyone who knows if you can convert v6 netres to 4 cyl .And if you can how you do it.



Re: Convert V6 Netres To V8
dont think you would need to when there are
plenty of 4 cyl netres floating around
plenty of 4 cyl netres floating around
Re: Convert V6 Netres To V8
4 cylinder is the same as 6 cylinder but with the resistors the other way around. its probably easyest to rip the chip out and solder in new 7.5k and 15k reistors so that the same 3 points are connected but with the resistors in the opposite positions.
Have you read the FAQ? For lots of information and links to significant threads see here: viewtopic.php?f=7&t=1396
- Holden202T
-
- Posts: 10093
- Joined: Sat Feb 28, 2009 9:05 pm
- Location: Tenambit, NSW
Re: Convert V6 Netres To V8
netres resistors. The factory TBI setting is used for 2 cylinder mode in OSE 12P.
- Attachments
-
- netres resistors.png (26.95 KiB) Viewed 9047 times
No matter what the question is, the answer is always more horsepower! 
Just starting out? Have a read of the getting started guide
Basic tuning of a delco ECM with $12P thread
Advanced tuning of a delco ECM with $12P thread

Just starting out? Have a read of the getting started guide
Basic tuning of a delco ECM with $12P thread
Advanced tuning of a delco ECM with $12P thread
Re: Convert V6 Netres To V8
This is v6 to v8 7.5k resistor
- Attachments
-
- V6-V8%20RESISTOR%20MOD.JPG (324.69 KiB) Viewed 9430 times
Return to Hardware Modification and Development
Who is online
Users browsing this forum: No registered users and 1 guest