Convert V6 Netres To V8

Ecu Hardware Modifications
User avatar
Posts: 2573
Joined: Sun Mar 01, 2009 8:59 am
Location: North Coast, NSW

Re: Convert V6 Netres To V8

Postby Jayme » Fri Aug 28, 2015 4:43 pm

From what I can see, you cut the 4th leg on the netres and you needed to cut the 5th leg to turn v6 to v8

Posts: 2432
Joined: Sun Aug 02, 2009 9:16 pm
Location: Bayside, Melbourne, Victoria

Re: Convert V6 Netres To V8

Postby VX L67 Getrag » Fri Aug 28, 2015 5:31 pm

from looking at the netres pictures it still needs that 5th leg for the 7.5k as thats what stock v8 has but removing the 4th(15k resistance) "SHOULD" do the trick but didn't seem to with either of these memcal's!

User avatar
Posts: 1020
Joined: Sat Apr 30, 2011 6:27 pm
Location: Narellan, NSW

Re: Convert V6 Netres To V8

Postby festy » Fri Aug 28, 2015 5:58 pm

Pin numbers start from top left -> bottom left, then bottom right ->top right so the one you cut is pin 13.
You need to re-join that one and cut pin 12 instead.

Posts: 2432
Joined: Sun Aug 02, 2009 9:16 pm
Location: Bayside, Melbourne, Victoria

Re: Convert V6 Netres To V8

Postby VX L67 Getrag » Fri Aug 28, 2015 6:34 pm

AHH bugger the photo that's in earlier post is wrong then, I wish I didn't break it off at the base now but I was pretty sure the photo I had in my memcal folder was the same as what I did last time, but obviously not!

Site Admin
User avatar
Posts: 5709
Joined: Sat Feb 28, 2009 8:34 pm

Re: Convert V6 Netres To V8

Postby antus » Sun Aug 30, 2015 1:33 pm

Yeah, the notch in the diagrams marks the same end as the dot next to pin one in your photos. In general (not just this thread) the way of marking pin one can vary between manufacturers, but the mark is pin 1 or pin 1 end. You can see in your pics that all the chips have some kind of notch, or dot down one end. Thats the chips reference point.
Have you read the FAQ? For lots of information and links to significant threads see here: viewtopic.php?f=7&t=1396

Posts: 30
Joined: Tue Oct 15, 2013 1:04 pm

Re: Convert V6 Netres To V8

Postby 4wheelinls1 » Thu Apr 14, 2016 1:59 pm

Has anyone used a VR-VS V6 chip successfully with the netres leg cut and knock board removed when using a stacked $12P tune in the 808? I have heaps of them but have had not had any success.

Cheers

Online
Posts: 3171
Joined: Mon Aug 02, 2010 6:35 pm

Re: Convert V6 Netres To V8

Postby Dylan » Thu Apr 14, 2016 3:45 pm

VR V6 chip yes plenty of times. Not socketd yet though but plenty with EEPROM'S fitted.

Posts: 30
Joined: Tue Oct 15, 2013 1:04 pm

Re: Convert V6 Netres To V8

Postby 4wheelinls1 » Fri Apr 15, 2016 9:50 am

Dylan wrote:VR V6 chip yes plenty of times. Not socketd yet though but plenty with EEPROM'S fitted.


So you have used the in VN-VP with 12P?

Online
Posts: 3171
Joined: Mon Aug 02, 2010 6:35 pm

Re: Convert V6 Netres To V8

Postby Dylan » Fri Apr 15, 2016 11:56 am

Plenty of times. You will need too stack 12P when burning to a VR V6 AUTO memcal as they are 512kb.

Site Admin
User avatar
Posts: 5709
Joined: Sat Feb 28, 2009 8:34 pm

Re: Convert V6 Netres To V8

Postby antus » Fri Apr 15, 2016 4:44 pm

yes 512K bit = 64K Byte so 2 copies of 12P in size (and the second copy is used as its all mapped from the end of the chip, not the start.)
Have you read the FAQ? For lots of information and links to significant threads see here: viewtopic.php?f=7&t=1396

PreviousNext

Return to Hardware Modification and Development

Who is online

Users browsing this forum: No registered users and 1 guest