NVRAM Board For The VS Ecotec and Later PCMs
Re: NVRAM Board For The VS Ecotec and Later PCMs
Nvram works i loaded a stock tune on runs fine but as soon as i connect the write pin it has a fit and i did notice the traction control light was on wich usually defaults off until you hit the switch and engine check light was on.
- Holden202T
- Posts: 10311
- Joined: Sat Feb 28, 2009 9:05 pm
- Location: Tenambit, NSW
- Contact:
Re: NVRAM Board For The VS Ecotec and Later PCMs
you wont be able to write with the vs code, need custom code (something like $12P but suitable for VS) so you can get cals in and out of it!
No matter what the question is, the answer is always more horsepower!
Just starting out? Have a read of the getting started guide
Basic tuning of a delco ECM with $12P thread
Advanced tuning of a delco ECM with $12P thread
Just starting out? Have a read of the getting started guide
Basic tuning of a delco ECM with $12P thread
Advanced tuning of a delco ECM with $12P thread
Re: NVRAM Board For The VS Ecotec and Later PCMs
Oh ok its a vt sc i thought i would be able to use tp to edit a standard tune and flashtool to upload new settings without removing it ?
- VL400
- Posts: 4991
- Joined: Sun Mar 01, 2009 2:54 pm
- cars: VL Calais and Toyota Landcruiser. Plus some toys :)
- Location: Perth, WA
- Contact:
Re: NVRAM Board For The VS Ecotec and Later PCMs
If only it was so easy You can only read from the bin - but the limitation there is you can only get the first bank of memory.Dec_head wrote:Oh ok its a vt sc i thought i would be able to use tp to edit a standard tune and flashtool to upload new settings without removing it ?
Re: NVRAM Board For The VS Ecotec and Later PCMs
Ah well car is pretty much stock just has a smaller pulley doubt i would be able to make much difference anyway so no great loss.
- delcowizzid
- Posts: 5493
- Joined: Sat Feb 28, 2009 8:38 pm
- Location: Wellington NZ
- Contact:
Re: NVRAM Board For The VS Ecotec and Later PCMs
stick the XU-6 tune in she will wake it up
If Its Got Gas Or Ass Count Me In.if it cant be fixed with a hammer you have an electrical problem
Re: NVRAM Board For The VS Ecotec and Later PCMs
Tried it already hard to tell if their is a difference in power if their is it must be minimal i did notice that gear changes seemed better.
Re: NVRAM Board For The VS Ecotec and Later PCMs
I have a Opel Vectra B ecm (GM 16202319) from 2000 , which has 40 pins on the board ... the chip is not on a memcal , rather is a 32 pin plcc AMD chip ...
So , is there an nvram adapter for my 40 pin board ?
So , is there an nvram adapter for my 40 pin board ?
- VL400
- Posts: 4991
- Joined: Sun Mar 01, 2009 2:54 pm
- cars: VL Calais and Toyota Landcruiser. Plus some toys :)
- Location: Perth, WA
- Contact:
Re: NVRAM Board For The VS Ecotec and Later PCMs
Sorry there is no NVRAM for any flash based PCMs yet
- vnsswithcam
- Posts: 79
- Joined: Sat Mar 20, 2010 1:20 pm
- cars: vt ss commodore
- Location: penrith n.s.w
Re: NVRAM Board For The VS Ecotec and Later PCMs
hi guys, ive got a vt ss 5 litre and ive got the nvram board for the vn-vs etc but i want to use my ds1245y-100 chip in a stock memcal board but before i give it a crack using the schematic im having some trouble understanding it the nvram side doesnt have vpp,pgm pin inputs? or am i reading it wrong is there a better way to understand this like a guide telling me pin 22 from pcm connector side goes to pin 1 on the ds1245-100 chip etc ,etc,and so on?
also what are the numbers on the nvram schematic eg:bottom left says 16 ground and ground on the pcm side is pin 31 and A16 above it has a 2 then you look at pcm side and A16 is pin 3 ? any help what are those numbers in order bottom left goes
16,2,31,3,28,4,25,23,26,27 etc,etc
also what are the numbers on the nvram schematic eg:bottom left says 16 ground and ground on the pcm side is pin 31 and A16 above it has a 2 then you look at pcm side and A16 is pin 3 ? any help what are those numbers in order bottom left goes
16,2,31,3,28,4,25,23,26,27 etc,etc
one point twenty one jiggawatts!!!! great scott!!!