Programmable Delco Ignition Module

Ecu Hardware Modifications
Posts: 701
Joined: Tue Jul 21, 2009 10:02 am

Re: Programmable Delco Ignition Module

Postby v6bucket » Thu Oct 26, 2017 12:18 pm

I'm setting up my 202 Holden with Delco Ign. Module, how much bigger than the balancer does the 36-1 trigger wheel need to be? The balancer is a 7" TCI Super Damper.
"Definition of a Drag Racer: A person who spends money he doesn't have on parts he doesn't need to impress people he doesn't know." - Grumpy Jenkins----- Poverty---

User avatar
Posts: 9755
Joined: Sat Feb 28, 2009 9:05 pm
Location: Tenambit, NSW

Re: Programmable Delco Ignition Module

Postby Holden202T » Fri Oct 27, 2017 12:09 pm

I went 6.5 I think ..... for a stock 6in balancer (from memory), but really it just needs to be the same size or bigger than the depth of the teeth so the base of the teeth are wider than the balancer.

Exhibit A

P1100743.jpg
P1100743.jpg (402.58 KiB) Viewed 2908 times

Posts: 701
Joined: Tue Jul 21, 2009 10:02 am

Re: Programmable Delco Ignition Module

Postby v6bucket » Fri Oct 27, 2017 11:12 pm

Thanks, I thought that was the case. Now to find a 7 1/2" wheel.
"Definition of a Drag Racer: A person who spends money he doesn't have on parts he doesn't need to impress people he doesn't know." - Grumpy Jenkins----- Poverty---

User avatar
Posts: 9755
Joined: Sat Feb 28, 2009 9:05 pm
Location: Tenambit, NSW

Re: Programmable Delco Ignition Module

Postby Holden202T » Sat Oct 28, 2017 8:45 am


Posts: 701
Joined: Tue Jul 21, 2009 10:02 am

Re: Programmable Delco Ignition Module

Postby v6bucket » Sat Oct 28, 2017 3:52 pm

I suppose it would, the sensor looks for the edge of the slot, correct? The front edge of the Super Damper is curved, so it shouldn't interfere with the signal, is that correct?
"Definition of a Drag Racer: A person who spends money he doesn't have on parts he doesn't need to impress people he doesn't know." - Grumpy Jenkins----- Poverty---

User avatar
Posts: 9755
Joined: Sat Feb 28, 2009 9:05 pm
Location: Tenambit, NSW

Re: Programmable Delco Ignition Module

Postby Holden202T » Sat Oct 28, 2017 4:09 pm

I just did a quick calc, it looks like you'd have 3mm of the teeth stick out above the balancer ... im not sure that's going to be enough ... it might interfere .... your probably right you need to find a 7.5

Posts: 558
Joined: Mon Jul 11, 2016 6:29 am

Re: Programmable Delco Ignition Module

Postby Wade » Sun Dec 03, 2017 9:28 pm

Has anyone got a cal file and wiring diagram for the module into ecotec v6?

Posts: 701
Joined: Tue Jul 21, 2009 10:02 am

Re: Programmable Delco Ignition Module

Postby v6bucket » Thu May 17, 2018 11:23 am

I'm back to the trigger wheel, after some house repairs & life getting in n the way. How deep does the tooth have to be?
"Definition of a Drag Racer: A person who spends money he doesn't have on parts he doesn't need to impress people he doesn't know." - Grumpy Jenkins----- Poverty---

User avatar
Posts: 9755
Joined: Sat Feb 28, 2009 9:05 pm
Location: Tenambit, NSW

Re: Programmable Delco Ignition Module

Postby Holden202T » Fri May 18, 2018 1:17 pm

Wade: I probably have a cal for a module into a VP I reckon it would be the same settings, but would also depend what version of the firmware we both have.

v6bucket: from memory it should be about the same as the width of the slot ?

Posts: 1
Joined: Tue Mar 21, 2017 1:31 am

Re: Programmable Delco Ignition Module

Postby -=Jeff=- » Sat Jul 13, 2019 1:00 pm

I thought it was time to reply.. I purchased a couple of these modules in July-August of 2018. This was purchased for my 1990 LT5 Corvette.. I got it running in November, then picked up again in Feb as Jan was a bit cold in Chicago.

It has been working quite well outside of the few wiring challenges I have had. I will get some pictures posted however, I have the LS coils in the location where the stock coils were and the Unit is under the dash.

I feel the car runs better/smoother with the Unit compared to the OEM unit

PreviousNext

Return to Hardware Modification and Development

Who is online

Users browsing this forum: No registered users and 2 guests