Programmable Delco Ignition Module
- vlad01
- Posts: 7803
- Joined: Mon Oct 08, 2012 6:41 pm
- cars: VP I S
VP I executive
VP II executive
VP II executive #2
VR II executive - Location: Kyneton, Vic
Re: Programmable Delco Ignition Module
Is it blue?
I'm the director of VSH (Vlad's Spec Holden), because HSV were doing it ass about.
Re: Programmable Delco Ignition Module
I'd like the next version to have a higher ip rating to suit us speedway guys
According to chemistry, alcohol is a solution...
-
- Posts: 3426
- Joined: Thu Apr 09, 2009 12:31 pm
- cars: VH, VN, VS, VX
Re: Programmable Delco Ignition Module
vlad01 wrote:Is it blue?
Yep.
- vlad01
- Posts: 7803
- Joined: Mon Oct 08, 2012 6:41 pm
- cars: VP I S
VP I executive
VP II executive
VP II executive #2
VR II executive - Location: Kyneton, Vic
Re: Programmable Delco Ignition Module
I'm the director of VSH (Vlad's Spec Holden), because HSV were doing it ass about.
- Holden202T
- Posts: 10311
- Joined: Sat Feb 28, 2009 9:05 pm
- Location: Tenambit, NSW
- Contact:
Re: Programmable Delco Ignition Module
VL400 wrote:some like to DIY everything as its all in the fine details of a build and others prefer just twist joining wires and ripping skids.
No matter what the question is, the answer is always more horsepower!
Just starting out? Have a read of the getting started guide
Basic tuning of a delco ECM with $12P thread
Advanced tuning of a delco ECM with $12P thread
Just starting out? Have a read of the getting started guide
Basic tuning of a delco ECM with $12P thread
Advanced tuning of a delco ECM with $12P thread
- vlad01
- Posts: 7803
- Joined: Mon Oct 08, 2012 6:41 pm
- cars: VP I S
VP I executive
VP II executive
VP II executive #2
VR II executive - Location: Kyneton, Vic
Re: Programmable Delco Ignition Module
We must be neighbors then given the side of the fence we sit on lol.
I'm the director of VSH (Vlad's Spec Holden), because HSV were doing it ass about.
- VL400
- Posts: 4991
- Joined: Sun Mar 01, 2009 2:54 pm
- cars: VL Calais and Toyota Landcruiser. Plus some toys :)
- Location: Perth, WA
- Contact:
Re: Programmable Delco Ignition Module
It does not have them as it does not need them with the current case have a slide in rail type mounting. But will add 4 extra pads for stand offs on the next run.vlad01 wrote:I noticed the board doesn't have off stand holes at the corners? Would be helpful if a custom case as per DYI is wanted by the customer to mount in any case they like, with a solid and flex free hold.
This is actually already possible. Removing the USB plug gives the data lines, power and shield pads that can be wired directly to a USB cable. It has been done. Its not good practice to have USB data lines ending as stubs, so adding a second set of pads for a standard 0.1" header is not really possible.vlad01 wrote:One other idea I have is maybe add a header for a USB cable so that if required a customer can plug in a cable and socket in any custom location giving freedom of both USB and main ignition socket instead of having them dictated by the locations on the board. Something like a 5 pin header , 2 of power, 2 for data and 1 for shield.
Had a quick play and the Delphi connector spacing means it is not easily possible to have a second set of holes, becomes very difficult actually. You would have to try and build your own interface board if you wanted this option.vlad01 wrote:As for the delphi connector, perhaps you could have dual through hole layout on the board slightly offset to each other to allow either option to be soldered in as required with the delphi header mounting holes also available which can double as 2 of the off stands I mentioned. So you can have one or 2 off stand holes at the back of the board (USB end) and the 2 holes for the delphi header for the front for 2 off stands and that also keeps the connector solid and rigid.
Otherwise a little header board with pads for the delphi bulkhead could be made and customers can simply use wires to ling the module to the header board., but its always more elegant to have it on the main board.
- vlad01
- Posts: 7803
- Joined: Mon Oct 08, 2012 6:41 pm
- cars: VP I S
VP I executive
VP II executive
VP II executive #2
VR II executive - Location: Kyneton, Vic
Re: Programmable Delco Ignition Module
Maybe you could make me a custom one
I'm the director of VSH (Vlad's Spec Holden), because HSV were doing it ass about.
- Holden202T
- Posts: 10311
- Joined: Sat Feb 28, 2009 9:05 pm
- Location: Tenambit, NSW
- Contact:
Re: Programmable Delco Ignition Module
you can get anything custom made at the right price
No matter what the question is, the answer is always more horsepower!
Just starting out? Have a read of the getting started guide
Basic tuning of a delco ECM with $12P thread
Advanced tuning of a delco ECM with $12P thread
Just starting out? Have a read of the getting started guide
Basic tuning of a delco ECM with $12P thread
Advanced tuning of a delco ECM with $12P thread
- vlad01
- Posts: 7803
- Joined: Mon Oct 08, 2012 6:41 pm
- cars: VP I S
VP I executive
VP II executive
VP II executive #2
VR II executive - Location: Kyneton, Vic
Re: Programmable Delco Ignition Module
efi connection added these after I asked about them. Pretty please can we haz ignition modules with these? The header is only 6.50 and the female plug body 1.60 each.
I can even order a whole bunch of them in for you as I need to make another order anyway.
https://www.eficonnection.com/home/prod ... ale-header
https://www.eficonnection.com/home/prod ... -connector
I can even order a whole bunch of them in for you as I need to make another order anyway.
https://www.eficonnection.com/home/prod ... ale-header
https://www.eficonnection.com/home/prod ... -connector
I'm the director of VSH (Vlad's Spec Holden), because HSV were doing it ass about.