Couldnt really find a section for this..
Re: Couldnt really find a section for this..
ok holden202s attempts at doing this has revived my interest to try this again i remade my adaptor and tried to get a read from it 9 out of 10 i just get random ff with some data inbetween and then i got this
i dont know if its correct but the bottom line looks totally different to the top line where as everyone elses looks the same second half top and bottom i dont know where im going wrong with thisRe: Couldnt really find a section for this..
ok i kept going over my gear and found i was tracing one track wrong and it wasnt actually connected so tried it again after fixing that issue and now im getting perfect reads tried a reprogram and it works flawlessly
- Holden202T
- Posts: 10311
- Joined: Sat Feb 28, 2009 9:05 pm
- Location: Tenambit, NSW
- Contact:
Re: Couldnt really find a section for this..
I've got my settings on VERYSLOW
I can program it no worries and when I read it back it is what I put into it.
I've tried a few different readings and they don't seem to like it, just get the 555555km reading, but when I put the original numbers back into it I get them showing up as it originally was, so it certainly seems to program correctly.
I can program it no worries and when I read it back it is what I put into it.
I've tried a few different readings and they don't seem to like it, just get the 555555km reading, but when I put the original numbers back into it I get them showing up as it originally was, so it certainly seems to program correctly.
No matter what the question is, the answer is always more horsepower!
Just starting out? Have a read of the getting started guide
Basic tuning of a delco ECM with $12P thread
Advanced tuning of a delco ECM with $12P thread
Just starting out? Have a read of the getting started guide
Basic tuning of a delco ECM with $12P thread
Advanced tuning of a delco ECM with $12P thread
Re: Couldnt really find a section for this..
So you've resolved this issue?Holden202T wrote: then every one in 10 or so one of the three in the red box is different usually by one character
Joe.
Re: Couldnt really find a section for this..
Did anyone ever check with an ohm-meter, if CN103 pin 1 actually connects to ground (eg. 74HC14 pin 7)?The1 wrote:with power on MM74HC14N has 5v on pin 2&3 and measuring across pin 1&2 has +5v on pin 2
Joe.
- Holden202T
- Posts: 10311
- Joined: Sat Feb 28, 2009 9:05 pm
- Location: Tenambit, NSW
- Contact:
Re: Couldnt really find a section for this..
well since I posted that info I haven't had a bad read so maybe it was just a dicky connection on the zif or something, only issue im having is getting it to program the numbers I want.... that's more a maths issue than anything else I think.
No matter what the question is, the answer is always more horsepower!
Just starting out? Have a read of the getting started guide
Basic tuning of a delco ECM with $12P thread
Advanced tuning of a delco ECM with $12P thread
Just starting out? Have a read of the getting started guide
Basic tuning of a delco ECM with $12P thread
Advanced tuning of a delco ECM with $12P thread
Re: Couldnt really find a section for this..
What numbers are you changing I just Copy straight from the dash tool and it works fine just change last 8 segments top and bottom lines
Re: Couldnt really find a section for this..
Is there a working version of this around?, I'm having the same issues as others where when this was fresh but the fix doesn't work anymore. That is from page 32festy wrote:Here's a quick and dirty calculator, just enter the desired odo reading at the top and it calculates the digits, checksums and block checksum, and does the endian conversion for you too.
I haven't tested it much but it looks like it calculates the right hex values for the couple of odo readings I've tried with it.
I was hoping to do it with an xdf for the dash bins, but couldn't work out a way to do the maths with TP so this is the best I could think of without spening too much time on it.
According to chemistry, alcohol is a solution...
- antus
- Site Admin
- Posts: 8251
- Joined: Sat Feb 28, 2009 8:34 pm
- cars: TX Gemini 2L Twincam
TX Gemini SR20 18psi
Datsun 1200 Ute
Subaru Blitzen '06 EZ30 4th gen, 3.0R Spec B - Contact:
Re: Couldnt really find a section for this..
I just tested it and it worked fine. Whats the error? Missing ocx?
If it is, i recommend installing the OCX files from this zip. The location to put them is different from 32bit windows and 64 bit windows, and you need to run a command prompt with admin rights (right click, run as administrator), then paste the instuctions to register the files. There are more in that zip than what are needed for the dash calculator, but they are a reasonably common set and are likely to make a bunch of older visual basic apps run on modern windows so you might as well do the lot. There are also different versions of these files around, I have found this collection to be good and stable. Same process works on win 10, despite the win7 in the filename.
If it is, i recommend installing the OCX files from this zip. The location to put them is different from 32bit windows and 64 bit windows, and you need to run a command prompt with admin rights (right click, run as administrator), then paste the instuctions to register the files. There are more in that zip than what are needed for the dash calculator, but they are a reasonably common set and are likely to make a bunch of older visual basic apps run on modern windows so you might as well do the lot. There are also different versions of these files around, I have found this collection to be good and stable. Same process works on win 10, despite the win7 in the filename.
- Attachments
-
- windows 7 ocx files.zip
- (1.52 MiB) Downloaded 287 times
Have you read the FAQ? For lots of information and links to significant threads see here: http://pcmhacking.net/forums/viewtopic.php?f=7&t=1396
Re: Couldnt really find a section for this..
sorry, I should have been more specific, the fault is missing 'mscomctl.ocx'
I downloaded the first one I found from here https://www.ocxme.com/download/3266/MSCOMCTL.OCX and installed it in syswow64 with no luck
Thanks heaps for the help
I downloaded the first one I found from here https://www.ocxme.com/download/3266/MSCOMCTL.OCX and installed it in syswow64 with no luck
Thanks heaps for the help
According to chemistry, alcohol is a solution...