XC barina / Corsa C Bcm 93c66 eeprom bin needed
XC barina / Corsa C Bcm 93c66 eeprom bin needed
Looking for
XC barina / Corsa C Bcm 93c66 eeprom bin file
RS
313203739
5WK4 8663
I reset it without doing the 10 second ignition cycle now it can't be reset or programmed
Thanks
Matt
XC barina / Corsa C Bcm 93c66 eeprom bin file
RS
313203739
5WK4 8663
I reset it without doing the 10 second ignition cycle now it can't be reset or programmed
Thanks
Matt
Fermec Software
For full versions email mattyjf01@hotmail.com
https://www.facebook.com/profile.php?id=100057603993203
For full versions email mattyjf01@hotmail.com
https://www.facebook.com/profile.php?id=100057603993203
Re: XC barina / Corsa C Bcm 93c66 eeprom bin needed
Here's 2 i have.
- Attachments
-
- 93c66-barinaxx-YE BCM-pin6492.bin
- (512 Bytes) Downloaded 85 times
-
- 93c66-barinaxx-VF BCM-pin1624.bin
- (512 Bytes) Downloaded 90 times
Re: XC barina / Corsa C Bcm 93c66 eeprom bin needed
Not what im looking for but thanks anywayThe1 wrote:Here's 2 i have.
Fermec Software
For full versions email mattyjf01@hotmail.com
https://www.facebook.com/profile.php?id=100057603993203
For full versions email mattyjf01@hotmail.com
https://www.facebook.com/profile.php?id=100057603993203
Re: XC barina / Corsa C Bcm 93c66 eeprom bin needed
What protocol was that using? ALDL, or CANbus?mattyjf01 wrote:Not what im looking for but thanks anyway
What error are you getting when it tries to security link? As in whats the error code on the comms line?
Your Local Aussie Reverse Engineer
Contact for Software/Hardware development and Reverse Engineering
Site:https://www.envyouscustoms.com
Mob:+61406 140 726
Contact for Software/Hardware development and Reverse Engineering
Site:https://www.envyouscustoms.com
Mob:+61406 140 726
Re: XC barina / Corsa C Bcm 93c66 eeprom bin needed
Kline using opcomTazzi wrote:What protocol was that using? ALDL, or CANbus?mattyjf01 wrote:Not what im looking for but thanks anyway
What error are you getting when it tries to security link? As in whats the error code on the comms line?
Wrong code using 0x27
Fermec Software
For full versions email mattyjf01@hotmail.com
https://www.facebook.com/profile.php?id=100057603993203
For full versions email mattyjf01@hotmail.com
https://www.facebook.com/profile.php?id=100057603993203
Re: XC barina / Corsa C Bcm 93c66 eeprom bin needed
Haven't worked out how to monitor an opcom or tech 2 kline session yet
only carprog
only carprog
Fermec Software
For full versions email mattyjf01@hotmail.com
https://www.facebook.com/profile.php?id=100057603993203
For full versions email mattyjf01@hotmail.com
https://www.facebook.com/profile.php?id=100057603993203
Re: XC barina / Corsa C Bcm 93c66 eeprom bin needed
Thanks Tazzi i adjusted the baud rate in my ALDL logger from 8192 to 10400Tazzi wrote:What protocol was that using? ALDL, or CANbus?mattyjf01 wrote:Not what im looking for but thanks anyway
What error are you getting when it tries to security link? As in whats the error code on the comms line?
Fermec Software
For full versions email mattyjf01@hotmail.com
https://www.facebook.com/profile.php?id=100057603993203
For full versions email mattyjf01@hotmail.com
https://www.facebook.com/profile.php?id=100057603993203
Re: XC barina / Corsa C Bcm 93c66 eeprom bin needed
Barina XC or Corsa C is both Kline 10400 and CAN bus mix
Re: XC barina / Corsa C Bcm 93c66 eeprom bin needed
Winning!mattyjf01 wrote:Thanks Tazzi i adjusted the baud rate in my ALDL logger from 8192 to 10400Tazzi wrote:What protocol was that using? ALDL, or CANbus?mattyjf01 wrote:Not what im looking for but thanks anyway
What error are you getting when it tries to security link? As in whats the error code on the comms line?
Your Local Aussie Reverse Engineer
Contact for Software/Hardware development and Reverse Engineering
Site:https://www.envyouscustoms.com
Mob:+61406 140 726
Contact for Software/Hardware development and Reverse Engineering
Site:https://www.envyouscustoms.com
Mob:+61406 140 726
Re: XC barina / Corsa C Bcm 93c66 eeprom bin needed
So after resetting a bcm you need to turn the ignition off for 10 seconds so it writes to eeprom then on again before programming.
This is the second time ive made this mistake( you would think i would of learnt after the first time).
Eeprom has two copies of the code but only one is zeroed out.
After you said ALDL i remembered not been able to monitor ALDL when tech2 was connected with some cables
I have a usb to uart board wired for receiving only(might be an arduino nano with default program).
It sends eg 1234
0x27 0x80 0x31 0x32 0x33 0x34
returns wrong code entered
0x7F 0x27 0x35
Ill try Zeroing out the eeprom if that doesnt work
Ill send
0x27 0x80 0x00 0x00 0x00 0x00
This is the second time ive made this mistake( you would think i would of learnt after the first time).
Eeprom has two copies of the code but only one is zeroed out.
After you said ALDL i remembered not been able to monitor ALDL when tech2 was connected with some cables
I have a usb to uart board wired for receiving only(might be an arduino nano with default program).
It sends eg 1234
0x27 0x80 0x31 0x32 0x33 0x34
returns wrong code entered
0x7F 0x27 0x35
Ill try Zeroing out the eeprom if that doesnt work
Ill send
0x27 0x80 0x00 0x00 0x00 0x00
Fermec Software
For full versions email mattyjf01@hotmail.com
https://www.facebook.com/profile.php?id=100057603993203
For full versions email mattyjf01@hotmail.com
https://www.facebook.com/profile.php?id=100057603993203