FS: VR - VY BCM Simulator

Hardware and Software. If you have something to sell, post it here.
Posts: 441
Joined: Thu May 03, 2012 10:50 pm
Location: Castlemaine, Vic

Re: FS: VR - VY BCM Simulator

Postby pman92 » Thu Jan 23, 2020 7:43 pm

I know VT/VX clusters can be programmed for no ABS or SRS easily enough with most decent scan tools (since they weren't always fitted, at least in VT models). But I don't think VY clusters can be since it was fitted to every vehicle by then (except maybe the ute version your referring to).

I can do 3 units for $350 AUD + postage to wherever you are.
It will probably take me about a week to setup and test it and then assemble 3 of them.

Cheers
VR-VY Holden BCM Simulator: LINK
Ford Smartlock Bypass Module: LINK

User avatar
Posts: 526
Joined: Thu May 09, 2013 6:50 pm

Re: FS: VR - VY BCM Simulator

Postby hsv08 » Thu Jan 23, 2020 7:46 pm

pman92 wrote:I know VT/VX clusters can be programmed for no ABS or SRS easily enough with most decent scan tools (since they weren't always fitted, at least in VT models). But I don't think VY clusters can be since it was fitted to every vehicle by then (except maybe the ute version your referring to).

I can do 3 units for $350 AUD + postage to wherever you are.
It will probably take me about a week to setup and test it and then assemble 3 of them.

Cheers


Perfect. I'll send you a PM to start organizing.

Posts: 1
Joined: Mon Dec 07, 2020 8:54 pm
Location: Paraguay

Re: FS: VR - VY BCM Simulator

Postby Travism » Mon Dec 07, 2020 9:06 pm

I have a vy adventra, Is this device able to turn off the abs error on my dash?

Posts: 211
Joined: Tue Oct 16, 2012 12:17 pm
Location: Perth

Re: FS: VR - VY BCM Simulator

Postby Tre-Cool » Mon Dec 07, 2020 10:25 pm

pman92 wrote:I know VT/VX clusters can be programmed for no ABS or SRS easily enough with most decent scan tools (since they weren't always fitted, at least in VT models). But I don't think VY clusters can be since it was fitted to every vehicle by then (except maybe the ute version your referring to).

I can do 3 units for $350 AUD + postage to wherever you are.
It will probably take me about a week to setup and test it and then assemble 3 of them.

Cheers


Can still be done in vy dash custer. my drag car just had ecu/pcm/bcm with a hsv lvl cluster.

u just mask the error.

Posts: 441
Joined: Thu May 03, 2012 10:50 pm
Location: Castlemaine, Vic

Re: FS: VR - VY BCM Simulator

Postby pman92 » Tue Dec 08, 2020 1:14 pm

Travism wrote:I have a vy adventra, Is this device able to turn off the abs error on my dash?


Only if it doesn't actually have ABS fitted. I would have to do a custom module to suit.
If the cluster can be programmed as Tre-Cool says it might be better/easier to do that though
VR-VY Holden BCM Simulator: LINK
Ford Smartlock Bypass Module: LINK

Posts: 441
Joined: Thu May 03, 2012 10:50 pm
Location: Castlemaine, Vic

Re: FS: VR - VY BCM Simulator

Postby pman92 » Sun Jan 10, 2021 2:30 pm

This modules had a bit of a V2.0 overhaul.
It's now all SMD components more suited to the application. And the PCB being assembled professionally in china makes quality better and more consistent and my job easier.
It's also now configurable for different applications, based on use cases I found from the previous one (that until now required custom firmware for that application). There's also plenty of room to expand and add different configurations when I find other potential uses (any ideas?).
Have a read of the first post for more information.
VR-VY Holden BCM Simulator: LINK
Ford Smartlock Bypass Module: LINK

Posts: 211
Joined: Tue Oct 16, 2012 12:17 pm
Location: Perth

Re: FS: VR - VY BCM Simulator

Postby Tre-Cool » Sun Aug 07, 2022 11:05 pm

I'd be keen on buying/working with you for a solution in replacing the older vz pim module to support the later can bus on the e38 ecu.

my vy ute uses a late 2010 model e38/6l80e & the vz 6lt pim does not like the late can bus data and causes the dash to go crazy. I mainly want something so i can plug the factory dash back in for the coolant temp guage to work. at the moment i use a powertune dash but that then results in no fuel gauge. next bonus would be having the factory aircon button trigger the ac pump via ecu too.

at the moment i just trigger the ac pump manually. In a factory arrangement i believe the ecu receives a constant broadcast to engage the ac pump.

Posts: 441
Joined: Thu May 03, 2012 10:50 pm
Location: Castlemaine, Vic

Re: FS: VR - VY BCM Simulator

Postby pman92 » Mon Aug 08, 2022 2:44 pm

Tre-Cool wrote:I'd be keen on buying/working with you for a solution in replacing the older vz pim module to support the later can bus on the e38 ecu.

my vy ute uses a late 2010 model e38/6l80e & the vz 6lt pim does not like the late can bus data and causes the dash to go crazy. I mainly want something so i can plug the factory dash back in for the coolant temp guage to work. at the moment i use a powertune dash but that then results in no fuel gauge. next bonus would be having the factory aircon button trigger the ac pump via ecu too.

at the moment i just trigger the ac pump manually. In a factory arrangement i believe the ecu receives a constant broadcast to engage the ac pump.


Sounds do-able, but I haven't really had anything to do with the later CAN bus stuff. How many different variety's of the data is there? Obviously it's changed between VZ and 2010?
VR-VY Holden BCM Simulator: LINK
Ford Smartlock Bypass Module: LINK

Posts: 211
Joined: Tue Oct 16, 2012 12:17 pm
Location: Perth

Re: FS: VR - VY BCM Simulator

Postby Tre-Cool » Mon Aug 08, 2022 9:35 pm

yeah apparently gm has an early & a late canbus. the data itself is almost identical. ive been told it's something kinda like this

0x0C9 84 0B CC 00 00 41 08 - Brake on -late
0x0C9 84 0B AA 00 00 41 08 - Brake on -early

Previous

Return to For Sale

Who is online

Users browsing this forum: No registered users and 2 guests