Delco DIS On Non DIS Engine
- antus
- Site Admin
- Posts: 8237
- Joined: Sat Feb 28, 2009 8:34 pm
- cars: TX Gemini 2L Twincam
TX Gemini SR20 18psi
Datsun 1200 Ute
Subaru Blitzen '06 EZ30 4th gen, 3.0R Spec B - Contact:
Re: Delco DIS On Non DIS Engine
what wiring diagram are you using? the wiring info in the 12p thread is correct. https://pcmhacking.net/forums/view ... f=27&t=356
Have you read the FAQ? For lots of information and links to significant threads see here: http://pcmhacking.net/forums/viewtopic.php?f=7&t=1396
Re: Delco DIS On Non DIS Engine
out of a Haynes manual for vn I knew I had seen it somewere thanks
- antus
- Site Admin
- Posts: 8237
- Joined: Sat Feb 28, 2009 8:34 pm
- cars: TX Gemini 2L Twincam
TX Gemini SR20 18psi
Datsun 1200 Ute
Subaru Blitzen '06 EZ30 4th gen, 3.0R Spec B - Contact:
Re: Delco DIS On Non DIS Engine
It should be correct, but if you doubt it grab the camira or pulsar wiring diagrams from the 12p thread linked above. Depending on what loom you have some of the wiring colours might be different, but the power ones will not be so if they dont match then you need to dig deeper.
Have you read the FAQ? For lots of information and links to significant threads see here: http://pcmhacking.net/forums/viewtopic.php?f=7&t=1396
Re: Delco DIS On Non DIS Engine
Yeah the colours don't worry me just the pinouts don't match across not references I'll just use the 12p info can some one please verify if this is a "yank" module
- antus
- Site Admin
- Posts: 8237
- Joined: Sat Feb 28, 2009 8:34 pm
- cars: TX Gemini 2L Twincam
TX Gemini SR20 18psi
Datsun 1200 Ute
Subaru Blitzen '06 EZ30 4th gen, 3.0R Spec B - Contact:
Re: Delco DIS On Non DIS Engine
Yeah, thats the right module. If you need a 6 pin connector send me a PM. I have a few left over from when I imported a batch.
Have you read the FAQ? For lots of information and links to significant threads see here: http://pcmhacking.net/forums/viewtopic.php?f=7&t=1396
-
- Posts: 440
- Joined: Sun Mar 22, 2009 11:52 am
- cars: VT V6 supercharged in a corolla
- Location: Sydney
- Contact:
Re: Delco DIS On Non DIS Engine
antus if you can spare another 6 pin connector please send me a PM and I will send you some money and my address.
Cheers
Dick
Cheers
Dick
Re: Delco DIS On Non DIS Engine
Sent you a pm antus
Re: Delco DIS On Non DIS Enigine
the commodore wrecker tells me that the plug for an ecotec knock sensor is the same as every other knock sensor???antus wrote: The 3 pin one can be found on the ecotech knock sensor on the front of the engine.
- Holden202T
- Posts: 10311
- Joined: Sat Feb 28, 2009 9:05 pm
- Location: Tenambit, NSW
- Contact:
Re: Delco DIS On Non DIS Engine
that's correct!
No matter what the question is, the answer is always more horsepower!
Just starting out? Have a read of the getting started guide
Basic tuning of a delco ECM with $12P thread
Advanced tuning of a delco ECM with $12P thread
Just starting out? Have a read of the getting started guide
Basic tuning of a delco ECM with $12P thread
Advanced tuning of a delco ECM with $12P thread
Re: Delco DIS On Non DIS Engine
ecotec knock sensor is a single pin connector, not a 3 pin. I suspect antus meant a different connector