265 Hemi to efi
-
- Posts: 1833
- Joined: Sat Aug 06, 2011 7:58 am
- cars: V8 VR Commodore BT1
LB Lancer 2L turbo & Delco
Starion TBI with Delco
Mitsubishi Lancer EVO4 track car
NA MX5
3 vintage motor bikes - Location: Padstow NSW
Re: 265 Hemi to efi
I think (don't quote me) that the primary voltage spikes to abt 400 volts when the plug fires. This can be picked up and measured on a scope (old piece of gear) if it gets too high it may be knocking out the module.
Re: 265 Hemi to efi
The motor starts leaning out at around 3800rpm so it needs 60lb injectors
https://www.ebay.com.au/itm/6-x-Siemens ... 1387641682
I found these which I assume would be compatIble for my setup but I measured my VX injectors and they at about 70mm, these say they are 60mm. I guess there is a bit of flexibility in the fuel rail mountings. Can anyone see any problems with this difference in length.
On the up side the tuner did some calculations and predicts this setup can achieve about 450hp at the flywheel but I won’t be going that far without forged pistons.
Cheers
https://www.ebay.com.au/itm/6-x-Siemens ... 1387641682
I found these which I assume would be compatIble for my setup but I measured my VX injectors and they at about 70mm, these say they are 60mm. I guess there is a bit of flexibility in the fuel rail mountings. Can anyone see any problems with this difference in length.
On the up side the tuner did some calculations and predicts this setup can achieve about 450hp at the flywheel but I won’t be going that far without forged pistons.
Cheers
- delcowizzid
- Posts: 5493
- Joined: Sat Feb 28, 2009 8:38 pm
- Location: Wellington NZ
- Contact:
Re: 265 Hemi to efi
Seimens are plug and play same length as stock injectors and will get you to around 500rwhp before you will need another upgrade
If Its Got Gas Or Ass Count Me In.if it cant be fixed with a hammer you have an electrical problem
Re: 265 Hemi to efi
thanks mate good to hear. 500rwhp yee ha.
-
- Posts: 1833
- Joined: Sat Aug 06, 2011 7:58 am
- cars: V8 VR Commodore BT1
LB Lancer 2L turbo & Delco
Starion TBI with Delco
Mitsubishi Lancer EVO4 track car
NA MX5
3 vintage motor bikes - Location: Padstow NSW
Re: 265 Hemi to efi
Ya gotta get it then keep it without breaking things. Should be possible with that big lugger engine. The only issue I see with shorter injectors is a possible air leak from the manifold if there not well intl the hole.
Re: 265 Hemi to efi
Picked it up tonight from the tuner and it just breaks traction it you give it a squirt Just need to keep the revs down at the moment so it doesn’t lean out.
It would be easy enough to adjust the fuel rail brackets if the injectors don’t sit low enough.
It would be easy enough to adjust the fuel rail brackets if the injectors don’t sit low enough.
Re: 265 Hemi to efi
Visited upullit today to get a spare ECM for the Ute and found a very tidy JE Camira that was recently added. I was only equipped with side cutters, a flat blade and Phillips head screwdriver but managed to remove the loom in less than an hour. Hardest bit was a metal loom clip that bolts to the block. I had to wriggle that up a down vigorously for 10 minutes before that snapped and released the loom. I just snipped the head bolt earths. $60 bargain.
- Attachments
-
- 4980338C-4AB6-45DD-9776-444E94E885D5.jpeg (132.38 KiB) Viewed 3429 times
- delcowizzid
- Posts: 5493
- Joined: Sat Feb 28, 2009 8:38 pm
- Location: Wellington NZ
- Contact:
Re: 265 Hemi to efi
Good score
If Its Got Gas Or Ass Count Me In.if it cant be fixed with a hammer you have an electrical problem
Re: 265 Hemi to efi
Yeah couldn’t believe my luck. There aren’t many JE Camira’s around anymore. Even the VN to VP Commodores are getting thin on the ground. Tonnes of VS VT Commodores though.
- Holden202T
- Posts: 10311
- Joined: Sat Feb 28, 2009 9:05 pm
- Location: Tenambit, NSW
- Contact:
Re: 265 Hemi to efi
yep get em while you still can!
No matter what the question is, the answer is always more horsepower!
Just starting out? Have a read of the getting started guide
Basic tuning of a delco ECM with $12P thread
Advanced tuning of a delco ECM with $12P thread
Just starting out? Have a read of the getting started guide
Basic tuning of a delco ECM with $12P thread
Advanced tuning of a delco ECM with $12P thread