Delco 808 conversion on Black 202 in a HR
- Holden202T
- Posts: 10311
- Joined: Sat Feb 28, 2009 9:05 pm
- Location: Tenambit, NSW
- Contact:
Re: Delco 808 conversion on Black 202 in a HR
its fine if you use it on a VS TB as its the right rotation for the sensor! its only a problem if you put a VS one on another TB!
No matter what the question is, the answer is always more horsepower!
Just starting out? Have a read of the getting started guide
Basic tuning of a delco ECM with $12P thread
Advanced tuning of a delco ECM with $12P thread
Just starting out? Have a read of the getting started guide
Basic tuning of a delco ECM with $12P thread
Advanced tuning of a delco ECM with $12P thread
Re: Delco 808 conversion on Black 202 in a HR
I don't know about the VN to VS TPS but certainly the VS V6 is different to the V8.
- Holden202T
- Posts: 10311
- Joined: Sat Feb 28, 2009 9:05 pm
- Location: Tenambit, NSW
- Contact:
Re: Delco 808 conversion on Black 202 in a HR
yeah talking about ecotec v6 TB, the vn-vr v6/8 and vs v8 are all the same.
No matter what the question is, the answer is always more horsepower!
Just starting out? Have a read of the getting started guide
Basic tuning of a delco ECM with $12P thread
Advanced tuning of a delco ECM with $12P thread
Just starting out? Have a read of the getting started guide
Basic tuning of a delco ECM with $12P thread
Advanced tuning of a delco ECM with $12P thread
Re: Delco 808 conversion on Black 202 in a HR
Cheers guys. I picked up a throttle body from a VT yesterday as they are the same as the VS, and it looked like it hadn't been sitting for too long. Also got the ignition gear off an N13 pulsar. Trips to the wreckers are fun!
Also for those blokes who are in brisbane the capalaba pick n pull wrecking yard is closing soon in the next couple of months, so get in whilst you can.
Also for those blokes who are in brisbane the capalaba pick n pull wrecking yard is closing soon in the next couple of months, so get in whilst you can.
Re: Delco 808 conversion on Black 202 in a HR
Good time to upgrade to a crank trigger and LS coils I say.
Re: Delco 808 conversion on Black 202 in a HR
Hey Holden202T, when fitting the MAT sensor (where the egr valve is) how did you rip out the egr pipe in the manifold? did you use a dremel or does it come out if you give it a tap and some force?
- Holden202T
- Posts: 10311
- Joined: Sat Feb 28, 2009 9:05 pm
- Location: Tenambit, NSW
- Contact:
Re: Delco 808 conversion on Black 202 in a HR
Pretty sure I just drilled it out till I was through the pipe and into the alloy, but I can't remember the size needed for tapping the thread
No matter what the question is, the answer is always more horsepower!
Just starting out? Have a read of the getting started guide
Basic tuning of a delco ECM with $12P thread
Advanced tuning of a delco ECM with $12P thread
Just starting out? Have a read of the getting started guide
Basic tuning of a delco ECM with $12P thread
Advanced tuning of a delco ECM with $12P thread
Re: Delco 808 conversion on Black 202 in a HR
Just starting a HD build, got a low k EFI 202 in great nic, would like to change from trimatic to 4 speed, just having issue locating JE Camira harness
- Holden202T
- Posts: 10311
- Joined: Sat Feb 28, 2009 9:05 pm
- Location: Tenambit, NSW
- Contact:
Re: Delco 808 conversion on Black 202 in a HR
you don't actually need a JE loom, you can use a VN/VP V6 commodore loom and just modify it to suit, but the JE loom is less work if you can find one.
No matter what the question is, the answer is always more horsepower!
Just starting out? Have a read of the getting started guide
Basic tuning of a delco ECM with $12P thread
Advanced tuning of a delco ECM with $12P thread
Just starting out? Have a read of the getting started guide
Basic tuning of a delco ECM with $12P thread
Advanced tuning of a delco ECM with $12P thread