converting harnes to vs 304 engine

Converting To Delco ECU From Carby Or Other Injection Systems
Humptydumpty
Posts: 58
Joined: Fri May 10, 2019 12:11 pm
cars: Toyota Bundera, Sr Hilux, Hilux workmate.
Location: Sydney

Re: converting harnes to vs 304 engine

Post by Humptydumpty »

Thanks that’s helpful!
Humptydumpty
Posts: 58
Joined: Fri May 10, 2019 12:11 pm
cars: Toyota Bundera, Sr Hilux, Hilux workmate.
Location: Sydney

Re: converting harnes to vs 304 engine

Post by Humptydumpty »

Cheers for that....
I’ll have to plumb up a t someplace so I can install my oil pressure sender...

Thanks
User avatar
Holden202T
Posts: 10311
Joined: Sat Feb 28, 2009 9:05 pm
Location: Tenambit, NSW
Contact:

Re: converting harnes to vs 304 engine

Post by Holden202T »

most parts shops will have the adaptor to do exactly what you want, can have the stock sensor in the end and a npt fitting out the side for a gauge etc.
Humptydumpty
Posts: 58
Joined: Fri May 10, 2019 12:11 pm
cars: Toyota Bundera, Sr Hilux, Hilux workmate.
Location: Sydney

Re: converting harnes to vs 304 engine

Post by Humptydumpty »

Can anyone confirm this is the correct Wirring to power up the ecu and system On a Vn ecu and Wirring loom.

- Purple/violet wire goes to pin 30 on relay (plus a positive supply wire to fuel pump from this same pin)

- relay pin 85 gets the green with white trace wire (this should be the wire that switches on relay wen ignition on) this is on a timer wen ignition is first turned on to start fuel pump?) not getting anything from this wire.



- relay pin 87 gets orange wire from oil pressure switch - the other side of oil pressure switch is direct to battery +(switches relay on once oil pressure is up) goes to relay pin 87

- relay pin 86 to body earth?


What am I missing? The red with black trace is getting a constant 12v from battery - the red wire is getting power from 2nd relay which is switching on and supplying power wen ignition is on. Earths are grounded. Igniter box is connected, dizzy is connected, coil is connected n injectors all plunges in etc....

Cheeeers
User avatar
Holden202T
Posts: 10311
Joined: Sat Feb 28, 2009 9:05 pm
Location: Tenambit, NSW
Contact:

Re: converting harnes to vs 304 engine

Post by Holden202T »

have a look at the picture i attached at the bottom of the 2nd page, that is what you need to make it work.
Humptydumpty
Posts: 58
Joined: Fri May 10, 2019 12:11 pm
cars: Toyota Bundera, Sr Hilux, Hilux workmate.
Location: Sydney

Re: converting harnes to vs 304 engine

Post by Humptydumpty »

Hey guys,
Appreciate all your help - I’ve got fuel pump relay working now :thumbup:


Another couple questions

Converting the Inlet air temp sensor from the VN to the vs/vt style - is that possible ? :comp: :comp: :comp: :geek:

Also can you tune these older ECUs? Like remap?

Cheeers
User avatar
Holden202T
Posts: 10311
Joined: Sat Feb 28, 2009 9:05 pm
Location: Tenambit, NSW
Contact:

Re: converting harnes to vs 304 engine

Post by Holden202T »

if your running a vn/vp computer then use the vn/vp/vr/vs s1 v8 sensor, the s2 VS and VT was the MAF ones, and im not sure if they are different or not.

as far as tuning, yes you can do all that with these.
Humptydumpty
Posts: 58
Joined: Fri May 10, 2019 12:11 pm
cars: Toyota Bundera, Sr Hilux, Hilux workmate.
Location: Sydney

Re: converting harnes to vs 304 engine

Post by Humptydumpty »

cheers ill do that

thanks for the help Holden202
vs ss
Posts: 591
Joined: Thu Nov 03, 2011 7:57 pm
cars: hsv enhanced vs ss
vt xu6
fb holden
toyota landcruiser
vt ss s1
Location: perth wa

Re: converting harnes to vs 304 engine

Post by vs ss »

Your engine would of had the small plastic one in the airbox.
You will have to drill and tap the manifold to fit the early sensor in.
The thread is 14x 1.5 and you can not just put the early one in the air box as the calibration is way off.
Humptydumpty
Posts: 58
Joined: Fri May 10, 2019 12:11 pm
cars: Toyota Bundera, Sr Hilux, Hilux workmate.
Location: Sydney

Re: converting harnes to vs 304 engine

Post by Humptydumpty »

Ok thanks mate...... so the Vs one won’t work that’s currently in the air box?
Cheers
Post Reply