Converting 202 to DIS

Converting To Delco ECU From Carby Or Other Injection Systems
Post Reply
inj gtr202
Posts: 156
Joined: Thu May 31, 2012 2:24 am
cars: LC GTR Torana
1982 FJ40

Converting 202 to DIS

Post by inj gtr202 »

Finally getting around to doing my engine install and conversion from the locked dizzy to a crank angle sensor/coil pack set up.
My main question is regarding the pickup position relative to tdc. Photo is taken with the motor at tdc.
Does this look right? Would the crank offset be the same as it was previously or will it need to be changed?
Attachments
IMG20230119205419.jpg
inj gtr202
Posts: 156
Joined: Thu May 31, 2012 2:24 am
cars: LC GTR Torana
1982 FJ40

Re: Converting 202 to DIS

Post by inj gtr202 »

Here are a few more progress pics
Attachments
IMG20230111152545.jpg
IMG20230116163109.jpg
inj gtr202
Posts: 156
Joined: Thu May 31, 2012 2:24 am
cars: LC GTR Torana
1982 FJ40

Re: Converting 202 to DIS

Post by inj gtr202 »

Custom pickup and injection manifold
Attachments
IMG20221231120609.jpg
IMG20230104212524.jpg
User avatar
vlad01
Posts: 7780
Joined: Mon Oct 08, 2012 6:41 pm
cars: VP I S
VP I executive
VP II executive
VP II executive #2
VR II executive
Location: Kyneton, Vic

Re: Converting 202 to DIS

Post by vlad01 »

That looks sweet as! :thumbup: Top job, can't wait to see it going.

Not sure on the trigger setup. The sensor looks too far from the wheel? Someone that's worked with trigger wheels will chime in I hope.

As for the angle of the sensor to TDC, I think that the reference angle in the tune maybe? :think:
I'm the director of VSH (Vlad's Spec Holden), because HSV were doing it ass about.
In-Tech
Posts: 778
Joined: Mon Mar 09, 2020 4:35 pm
Location: California

Re: Converting 202 to DIS

Post by In-Tech »

Awesome work :) Try to bracket that pickup tube, vibration and time will take its' toll on it unsupported.
inj gtr202
Posts: 156
Joined: Thu May 31, 2012 2:24 am
cars: LC GTR Torana
1982 FJ40

Re: Converting 202 to DIS

Post by inj gtr202 »

In-Tech wrote:Awesome work :) Try to bracket that pickup tube, vibration and time will take its' toll on it unsupported.
The photo doesn't show it very well but it is supported by the factory bracket clamp position. I heated up the original and tigged it to the new one.
Fingers crossed there are no pin holes :wtf:
In-Tech
Posts: 778
Joined: Mon Mar 09, 2020 4:35 pm
Location: California

Re: Converting 202 to DIS

Post by In-Tech »

I see it now :thumbup:
heff0018
Posts: 888
Joined: Tue Apr 21, 2015 1:42 pm
cars: CL valiant charger, VH valiant charger

Re: Converting 202 to DIS

Post by heff0018 »

Nice work.
Mechcano
Posts: 19
Joined: Wed Jan 06, 2010 3:45 pm

Re: Converting 202 to DIS

Post by Mechcano »

My main question is regarding the pickup position relative to tdc. Photo is taken with the motor at tdc.
Does this look right?
No it does not look right, the Notch to the right of the Sync Notch, at TDC should align with the sensor. When the engine is rotated a further 10deg the sensor should align with the Sync Notch.

Here is a copy from the Megasquirt site on the setup for this module http://www.useasydocs.com/details/GM_DIS.htm

The picture in the url below shows the relationship between the Notch and Sync Notch when near TDC.

https://postimg.cc/RNH2xcb9
inj gtr202
Posts: 156
Joined: Thu May 31, 2012 2:24 am
cars: LC GTR Torana
1982 FJ40

Re: Converting 202 to DIS

Post by inj gtr202 »

Thank you for your information.
I think I have my head around it now.
I have measured where the TDC notch and sync notch are relative to the sensor at TDC.
The TDC notch is exactly 90deg before TDC as it passes the sensor.
So I'm guessing I just need to enter a reference value of 90deg as a spark offset in the ecu.
Attachments
IMG20230129163102.jpg
IMG20230129161929.jpg
Post Reply