FX Holden Race Car Project
- jenko
- Posts: 450
- Joined: Wed Jan 29, 2014 3:43 pm
- cars: hilux v6
jaguar v12
mitsubishi lancer
fj cruiser
sv 21 camry wagon - Location: Pine mountain .vic
- Contact:
Re: FX Holden Race Car Project
been looking for hours ,good work but no reference
- Holden202T
- Posts: 10311
- Joined: Sat Feb 28, 2009 9:05 pm
- Location: Tenambit, NSW
- Contact:
Re: FX Holden Race Car Project
didn't have much reference till after work was completed, was too hot, water only!
No matter what the question is, the answer is always more horsepower!
Just starting out? Have a read of the getting started guide
Basic tuning of a delco ECM with $12P thread
Advanced tuning of a delco ECM with $12P thread
Just starting out? Have a read of the getting started guide
Basic tuning of a delco ECM with $12P thread
Advanced tuning of a delco ECM with $12P thread
- vlad01
- Posts: 7795
- Joined: Mon Oct 08, 2012 6:41 pm
- cars: VP I S
VP I executive
VP II executive
VP II executive #2
VR II executive - Location: Kyneton, Vic
Re: FX Holden Race Car Project
I see I have started a problem with this "where's reference?" by doing the first one without warning.
where, where, where's reference? ah there he is.
where, where, where's reference? ah there he is.
I'm the director of VSH (Vlad's Spec Holden), because HSV were doing it ass about.
- Holden202T
- Posts: 10311
- Joined: Sat Feb 28, 2009 9:05 pm
- Location: Tenambit, NSW
- Contact:
Re: FX Holden Race Car Project
while I've been flat out trying to fix my daily driver I at least put a bit of time aside to fit up my latest purchase
I've always struggled to find a spot to sit the steering wheel in the gemini other than just on the passenger side floor, and I bought two of these one for the steering wheel and one for the helmet, it will most likely go on the roof diagonal bar.
I've always struggled to find a spot to sit the steering wheel in the gemini other than just on the passenger side floor, and I bought two of these one for the steering wheel and one for the helmet, it will most likely go on the roof diagonal bar.
No matter what the question is, the answer is always more horsepower!
Just starting out? Have a read of the getting started guide
Basic tuning of a delco ECM with $12P thread
Advanced tuning of a delco ECM with $12P thread
Just starting out? Have a read of the getting started guide
Basic tuning of a delco ECM with $12P thread
Advanced tuning of a delco ECM with $12P thread
- Holden202T
- Posts: 10311
- Joined: Sat Feb 28, 2009 9:05 pm
- Location: Tenambit, NSW
- Contact:
Re: FX Holden Race Car Project
heres some reference and a floor panel template
No matter what the question is, the answer is always more horsepower!
Just starting out? Have a read of the getting started guide
Basic tuning of a delco ECM with $12P thread
Advanced tuning of a delco ECM with $12P thread
Just starting out? Have a read of the getting started guide
Basic tuning of a delco ECM with $12P thread
Advanced tuning of a delco ECM with $12P thread
Re: FX Holden Race Car Project
I normally put the steering wheel on the column ! Unless my reference point is to big lol I would’ve thought drivers seat was in back seat ?
-
- Posts: 155
- Joined: Wed Jan 07, 2015 1:21 pm
- cars: hj ute, hz wagon, copious amounts of random half started side projects
- Location: Mid North Coast
Re: FX Holden Race Car Project
1/8th mile drags might be happening at taree airport, at the start/mid way through next year, should have it done by than maybe?
why have one 202, when you can have 12 and counting, 30+ car graveyard just for fun aswell
- Holden202T
- Posts: 10311
- Joined: Sat Feb 28, 2009 9:05 pm
- Location: Tenambit, NSW
- Contact:
Re: FX Holden Race Car Project
fuck yeah i'd definitely be keen for that! that's like just over 2hrs away!
No matter what the question is, the answer is always more horsepower!
Just starting out? Have a read of the getting started guide
Basic tuning of a delco ECM with $12P thread
Advanced tuning of a delco ECM with $12P thread
Just starting out? Have a read of the getting started guide
Basic tuning of a delco ECM with $12P thread
Advanced tuning of a delco ECM with $12P thread
- Holden202T
- Posts: 10311
- Joined: Sat Feb 28, 2009 9:05 pm
- Location: Tenambit, NSW
- Contact:
Re: FX Holden Race Car Project
despite the extreme heat and mugginess yesterday we made really good progress, and the driver side floor is now in!
still more welding to go obviously, but did the bare minimum in the heat to get the floor sorted....
still more welding to go obviously, but did the bare minimum in the heat to get the floor sorted....
No matter what the question is, the answer is always more horsepower!
Just starting out? Have a read of the getting started guide
Basic tuning of a delco ECM with $12P thread
Advanced tuning of a delco ECM with $12P thread
Just starting out? Have a read of the getting started guide
Basic tuning of a delco ECM with $12P thread
Advanced tuning of a delco ECM with $12P thread