CF Bedford Van

Post Your Delco Powered Ride Here
User avatar
Holden202T
Posts: 10311
Joined: Sat Feb 28, 2009 9:05 pm
Location: Tenambit, NSW
Contact:

Re: CF Bedford Van

Post by Holden202T »

yeah its not the smallest!
ac size.jpg
ac size.jpg (55.22 KiB) Viewed 5089 times
User avatar
Holden202T
Posts: 10311
Joined: Sat Feb 28, 2009 9:05 pm
Location: Tenambit, NSW
Contact:

Re: CF Bedford Van

Post by Holden202T »

First things first, I wanted to sus out all the wiring and controls to see how they all went together, so I did a little test, man it pumps some air! and there are 25 clicks from the lowest speed setting to flat out!

[youtube]http://www.youtube.com/watch?v=80vvA_Nt5wA[/youtube]

With that sorted it was time to cut into the dash and make this behemoth fit! Its not perfect at the moment, i'd like to get it a bit higher if I can, but generally its up under the dash and workable, but it is going to require the engine cover to be lower, which is not a problem, there was approx. 120-140mm of air gap between the top of the motor and the engine cover, so i'll re-design that as some stage.

I also got a Y piece from Bunnings plumbing section which is the perfect size for the flexible duct to slot into (its mounted behind the vice grips in the picture), so that has connected up the centre and passenger side factory window demister vents to one fitting of the A/C unit, and the second fitting will be dedicated to the driver side vent, once I get some more duct ... my theory is if the two vents out of the A/C unit blow the same pressure it will hopefully mean slightly more air out the driver side vent which is the one you want to work the best, it will also have a straight shot into the vent from the A/C unit, whereas the centre/passenger side ones turn.
20171029_144546_1509257401021_resized.jpg
And with the dash roughly sat back in place, looks like the 4 holes for the dash facing vents will be pretty easy to setup with the location of the outlets in the centre of the VR/VS dash and I have two eyeball vents on order for the ends of the dash.
20171029_144517_1509257403091_resized.jpg
User avatar
firebug
Posts: 184
Joined: Tue Jul 07, 2015 2:06 pm
cars: Pathfinder Ti 550, L67 Gemini
Location: Newcastle NSW

Re: CF Bedford Van

Post by firebug »

Image
"My favourite colour of the alphabet is 3!"
User avatar
Holden202T
Posts: 10311
Joined: Sat Feb 28, 2009 9:05 pm
Location: Tenambit, NSW
Contact:

Re: CF Bedford Van

Post by Holden202T »

hahahah that's what I'm hoping for :D
User avatar
Holden202T
Posts: 10311
Joined: Sat Feb 28, 2009 9:05 pm
Location: Tenambit, NSW
Contact:

Re: CF Bedford Van

Post by Holden202T »

Got all the rest of the bits, now to make them all fit into the Bedford :)
23192480_10156897722627501_752521773_o.jpg
Missus is doing stuff most of the weekend, so theres going to be a lot of time spent in the shed this weekend :punk:
User avatar
Holden202T
Posts: 10311
Joined: Sat Feb 28, 2009 9:05 pm
Location: Tenambit, NSW
Contact:

Re: CF Bedford Van

Post by Holden202T »

Made some good progress yesterday on the condenser, I think everything is going to just fit! ... although I'm not so sure about the A/C pump :think:
20171104_151314_1509835475377_resized.jpg
20171104_194755_1509835473440_resized.jpg
I will need to get a 45 degree fitting for the bottom A/C connection on the condenser but other wise I think it will be fine.
20171104_194804_1509835471500_resized.jpg
There is more tweaking to do but there is about 5mm gap here, and i''ll trim the snout of the water pump for good measure.
20171104_194839_1509835468899_resized.jpg
brindo
Posts: 199
Joined: Mon Jun 29, 2009 9:43 am
Location: Western Queensland

Re: CF Bedford Van

Post by brindo »

On my old WB ute, I copied the VT alternator bracket and mounted the AC compressor where the alternator would usually fit. Ran the belt straight from the crank pulley to the compressor and had an idler pulley in there to tension the belt.

And used a Commodore bracket to mount the alternator on the right hand side head. Didn’t have power steering to worry about though, but kept it all neat at least and allowed the AC pump to sit underneath the standard manifold.
User avatar
Holden202T
Posts: 10311
Joined: Sat Feb 28, 2009 9:05 pm
Location: Tenambit, NSW
Contact:

Re: CF Bedford Van

Post by Holden202T »

i've had a bit of a look at it today, theres enough room on the driver side to mount it, its just making sure it clears the steering rack while keeping it as far from the exhaust as I can, hopefully should be workable :)
User avatar
jenko
Posts: 450
Joined: Wed Jan 29, 2014 3:43 pm
cars: hilux v6
jaguar v12
mitsubishi lancer
fj cruiser
sv 21 camry wagon
Location: Pine mountain .vic
Contact:

Re: CF Bedford Van

Post by jenko »

was that a new tig welder I saw ?
User avatar
Holden202T
Posts: 10311
Joined: Sat Feb 28, 2009 9:05 pm
Location: Tenambit, NSW
Contact:

Re: CF Bedford Van

Post by Holden202T »

yeah sure is jenko, got it a few weeks ago!
Post Reply