FX Holden Race Car Project
- jenko
- Posts: 450
- Joined: Wed Jan 29, 2014 3:43 pm
- cars: hilux v6
jaguar v12
mitsubishi lancer
fj cruiser
sv 21 camry wagon - Location: Pine mountain .vic
- Contact:
Re: FX Holden Race Car Project
geat stuff
- Holden202T
- Posts: 10311
- Joined: Sat Feb 28, 2009 9:05 pm
- Location: Tenambit, NSW
- Contact:
Re: FX Holden Race Car Project
Front sump seal.Charlescrown wrote:Sump leak! Sure it's not the factory leaky rear main seal?
No matter what the question is, the answer is always more horsepower!
Just starting out? Have a read of the getting started guide
Basic tuning of a delco ECM with $12P thread
Advanced tuning of a delco ECM with $12P thread
Just starting out? Have a read of the getting started guide
Basic tuning of a delco ECM with $12P thread
Advanced tuning of a delco ECM with $12P thread
- Holden202T
- Posts: 10311
- Joined: Sat Feb 28, 2009 9:05 pm
- Location: Tenambit, NSW
- Contact:
Re: FX Holden Race Car Project
No matter what the question is, the answer is always more horsepower!
Just starting out? Have a read of the getting started guide
Basic tuning of a delco ECM with $12P thread
Advanced tuning of a delco ECM with $12P thread
Just starting out? Have a read of the getting started guide
Basic tuning of a delco ECM with $12P thread
Advanced tuning of a delco ECM with $12P thread
- vlad01
- Posts: 7796
- Joined: Mon Oct 08, 2012 6:41 pm
- cars: VP I S
VP I executive
VP II executive
VP II executive #2
VR II executive - Location: Kyneton, Vic
Re: FX Holden Race Car Project
I'm the director of VSH (Vlad's Spec Holden), because HSV were doing it ass about.
- delcowizzid
- Posts: 5493
- Joined: Sat Feb 28, 2009 8:38 pm
- Location: Wellington NZ
- Contact:
Re: FX Holden Race Car Project
Sounding good
If Its Got Gas Or Ass Count Me In.if it cant be fixed with a hammer you have an electrical problem
- VL400
- Posts: 4991
- Joined: Sun Mar 01, 2009 2:54 pm
- cars: VL Calais and Toyota Landcruiser. Plus some toys :)
- Location: Perth, WA
- Contact:
Re: FX Holden Race Car Project
Nice work! Sounds tough as.
Hopefully much reference was also consumed post startup while taking in the methanol fumes.
Hopefully much reference was also consumed post startup while taking in the methanol fumes.
Re: FX Holden Race Car Project
Sounds tuff ! Check your letter box tomorrow,
I've just sent a fine to you for no reference in the vid
I've just sent a fine to you for no reference in the vid
- Holden202T
- Posts: 10311
- Joined: Sat Feb 28, 2009 9:05 pm
- Location: Tenambit, NSW
- Contact:
Re: FX Holden Race Car Project
hahahahah
No matter what the question is, the answer is always more horsepower!
Just starting out? Have a read of the getting started guide
Basic tuning of a delco ECM with $12P thread
Advanced tuning of a delco ECM with $12P thread
Just starting out? Have a read of the getting started guide
Basic tuning of a delco ECM with $12P thread
Advanced tuning of a delco ECM with $12P thread
- Holden202T
- Posts: 10311
- Joined: Sat Feb 28, 2009 9:05 pm
- Location: Tenambit, NSW
- Contact:
Re: FX Holden Race Car Project
I have spent some time since getting the motor going to finish off a lot of the stuff that 1. I didn't have parts for or 2. wasn't needed to get the motor running at the time.
Things like oil catch can, boost controller and inlet piping is all pretty much worked out.... need to get the clamps for the piping still and make a few brackets to hold the piping in place etc .... oh and probably spend another $300-$400 on speedflow parts lol .... but I want all the vacuum hoses in braided/speedflow fittings so I can't complain
Things like oil catch can, boost controller and inlet piping is all pretty much worked out.... need to get the clamps for the piping still and make a few brackets to hold the piping in place etc .... oh and probably spend another $300-$400 on speedflow parts lol .... but I want all the vacuum hoses in braided/speedflow fittings so I can't complain
No matter what the question is, the answer is always more horsepower!
Just starting out? Have a read of the getting started guide
Basic tuning of a delco ECM with $12P thread
Advanced tuning of a delco ECM with $12P thread
Just starting out? Have a read of the getting started guide
Basic tuning of a delco ECM with $12P thread
Advanced tuning of a delco ECM with $12P thread