DELCOS NEW RIDE
- delcowizzid
- Posts: 5493
- Joined: Sat Feb 28, 2009 8:38 pm
- Location: Wellington NZ
- Contact:
Re: DELCOS NEW RIDE
This is them
If Its Got Gas Or Ass Count Me In.if it cant be fixed with a hammer you have an electrical problem
- oldn64
- Posts: 256
- Joined: Mon May 28, 2018 5:05 pm
- cars: Vq Statesman, VE SS wagon, VE Sv6, VY SV8, VL Belina
- Location: Country Victoria on a direct road to WINTON
Re: DELCOS NEW RIDE
Pads and caliper does look familiar.... (excuse the pun)
Might have to rip off a wheel when I get home and have a look at the TX3. wish i could get a caliper rebuild kit for the rear of this thing... have a seized one and cannot get a kit anywhere PBR dont even make one
cheers
oldn64
Might have to rip off a wheel when I get home and have a look at the TX3. wish i could get a caliper rebuild kit for the rear of this thing... have a seized one and cannot get a kit anywhere PBR dont even make one
cheers
oldn64
- delcowizzid
- Posts: 5493
- Joined: Sat Feb 28, 2009 8:38 pm
- Location: Wellington NZ
- Contact:
Re: DELCOS NEW RIDE
Bit of firewall in scored half a sheet of panel steel today
If Its Got Gas Or Ass Count Me In.if it cant be fixed with a hammer you have an electrical problem
-
- Posts: 3424
- Joined: Thu Apr 09, 2009 12:31 pm
- cars: VH, VN, VS, VX
Re: DELCOS NEW RIDE
I'm not seeing any CAD work....
- delcowizzid
- Posts: 5493
- Joined: Sat Feb 28, 2009 8:38 pm
- Location: Wellington NZ
- Contact:
Re: DELCOS NEW RIDE
Can't tack cad to steel lol just go at it lol
If Its Got Gas Or Ass Count Me In.if it cant be fixed with a hammer you have an electrical problem
- Holden202T
- Posts: 10311
- Joined: Sat Feb 28, 2009 9:05 pm
- Location: Tenambit, NSW
- Contact:
Re: DELCOS NEW RIDE
the gearbox is going to take up half the cabin hehe!
No matter what the question is, the answer is always more horsepower!
Just starting out? Have a read of the getting started guide
Basic tuning of a delco ECM with $12P thread
Advanced tuning of a delco ECM with $12P thread
Just starting out? Have a read of the getting started guide
Basic tuning of a delco ECM with $12P thread
Advanced tuning of a delco ECM with $12P thread
- delcowizzid
- Posts: 5493
- Joined: Sat Feb 28, 2009 8:38 pm
- Location: Wellington NZ
- Contact:
Re: DELCOS NEW RIDE
I'll do the whole bellhousing budge done in the thinner sheet first then I'll make the middle in 3mm so I don't need a seperate scatter sheild
If Its Got Gas Or Ass Count Me In.if it cant be fixed with a hammer you have an electrical problem
- oldn64
- Posts: 256
- Joined: Mon May 28, 2018 5:05 pm
- cars: Vq Statesman, VE SS wagon, VE Sv6, VY SV8, VL Belina
- Location: Country Victoria on a direct road to WINTON
Re: DELCOS NEW RIDE
That sounds very defeatist Delco, you thinking you will blow it up????delcowizzid wrote:I'll do the whole bellhousing budge done in the thinner sheet first then I'll make the middle in 3mm so I don't need a seperate scatter sheild
cheers
oldn64
-
- Posts: 3424
- Joined: Thu Apr 09, 2009 12:31 pm
- cars: VH, VN, VS, VX
Re: DELCOS NEW RIDE
Probably more a requirement when going faster than a certain ET/speed.
- vlad01
- Posts: 7795
- Joined: Mon Oct 08, 2012 6:41 pm
- cars: VP I S
VP I executive
VP II executive
VP II executive #2
VR II executive - Location: Kyneton, Vic
Re: DELCOS NEW RIDE
I definitely would want more shielding seeing how close the TC and trans is are in line with your legs. Those things when they explode are terrifying even with a Kevlar blanket.
Seen plenty shoot their guts through all the shielding, tunnel door and roof. Luck all failures I had seen were out the right ride on LHD cars. They seem to all explode out on the right side, not a good thing for RHD lol
Seen plenty shoot their guts through all the shielding, tunnel door and roof. Luck all failures I had seen were out the right ride on LHD cars. They seem to all explode out on the right side, not a good thing for RHD lol
I'm the director of VSH (Vlad's Spec Holden), because HSV were doing it ass about.