DELCOS NEW RIDE
- delcowizzid
- Posts: 5493
- Joined: Sat Feb 28, 2009 8:38 pm
- Location: Wellington NZ
- Contact:
Re: DELCOS NEW RIDE
I think it's the steel God knows what mix it is could be Chinese shit I know the steel of the body welds nicer lol
If Its Got Gas Or Ass Count Me In.if it cant be fixed with a hammer you have an electrical problem
- Holden202T
- Posts: 10311
- Joined: Sat Feb 28, 2009 9:05 pm
- Location: Tenambit, NSW
- Contact:
Re: DELCOS NEW RIDE
lol
No matter what the question is, the answer is always more horsepower!
Just starting out? Have a read of the getting started guide
Basic tuning of a delco ECM with $12P thread
Advanced tuning of a delco ECM with $12P thread
Just starting out? Have a read of the getting started guide
Basic tuning of a delco ECM with $12P thread
Advanced tuning of a delco ECM with $12P thread
- delcowizzid
- Posts: 5493
- Joined: Sat Feb 28, 2009 8:38 pm
- Location: Wellington NZ
- Contact:
Re: DELCOS NEW RIDE
Tidiest part yet lol
If Its Got Gas Or Ass Count Me In.if it cant be fixed with a hammer you have an electrical problem
- Holden202T
- Posts: 10311
- Joined: Sat Feb 28, 2009 9:05 pm
- Location: Tenambit, NSW
- Contact:
Re: DELCOS NEW RIDE
nice!
your getting stuck right in!
your getting stuck right in!
No matter what the question is, the answer is always more horsepower!
Just starting out? Have a read of the getting started guide
Basic tuning of a delco ECM with $12P thread
Advanced tuning of a delco ECM with $12P thread
Just starting out? Have a read of the getting started guide
Basic tuning of a delco ECM with $12P thread
Advanced tuning of a delco ECM with $12P thread
- delcowizzid
- Posts: 5493
- Joined: Sat Feb 28, 2009 8:38 pm
- Location: Wellington NZ
- Contact:
Re: DELCOS NEW RIDE
But of a slow down now I can't weld that peice in yet I need to cut the lower 4 link bar and fit an oval loop for the shaft to pass through to lower the middle a little or the driveshaft is going to hit the bottom bar on rebound
If Its Got Gas Or Ass Count Me In.if it cant be fixed with a hammer you have an electrical problem
- delcowizzid
- Posts: 5493
- Joined: Sat Feb 28, 2009 8:38 pm
- Location: Wellington NZ
- Contact:
Re: DELCOS NEW RIDE
Either that or I goto 32" tyres lol
If Its Got Gas Or Ass Count Me In.if it cant be fixed with a hammer you have an electrical problem
- Holden202T
- Posts: 10311
- Joined: Sat Feb 28, 2009 9:05 pm
- Location: Tenambit, NSW
- Contact:
Re: DELCOS NEW RIDE
lol why not
No matter what the question is, the answer is always more horsepower!
Just starting out? Have a read of the getting started guide
Basic tuning of a delco ECM with $12P thread
Advanced tuning of a delco ECM with $12P thread
Just starting out? Have a read of the getting started guide
Basic tuning of a delco ECM with $12P thread
Advanced tuning of a delco ECM with $12P thread
- delcowizzid
- Posts: 5493
- Joined: Sat Feb 28, 2009 8:38 pm
- Location: Wellington NZ
- Contact:
Re: DELCOS NEW RIDE
Think I'm going to go $11p and run the 4l60e I was using for mockup for now can't afford a real gearbox so might employ some electronics and sort of cheat should be consistent as if I let the ecu do all the shifting be just like having an air shifted promod lol apart from the gearbox longevity lol I need to get a good $11p turbo base tune sorted anyway and I have the box
If Its Got Gas Or Ass Count Me In.if it cant be fixed with a hammer you have an electrical problem
- vlad01
- Posts: 7798
- Joined: Mon Oct 08, 2012 6:41 pm
- cars: VP I S
VP I executive
VP II executive
VP II executive #2
VR II executive - Location: Kyneton, Vic
Re: DELCOS NEW RIDE
Better have 2 layers of shatter shields for your legs, you know with 4l60Es and all.
I'm the director of VSH (Vlad's Spec Holden), because HSV were doing it ass about.
- delcowizzid
- Posts: 5493
- Joined: Sat Feb 28, 2009 8:38 pm
- Location: Wellington NZ
- Contact:
Re: DELCOS NEW RIDE
HAHA some chainsaw chaps as a 2nd layer of protection you reckon lol
If Its Got Gas Or Ass Count Me In.if it cant be fixed with a hammer you have an electrical problem