mitsubishi evo 7 tuning tephra mod software

Posts: 119
Joined: Mon Dec 07, 2009 2:14 pm

mitsubishi evo 7 tuning tephra mod software

Postby jca » Tue Oct 23, 2018 7:52 pm

hi guys im wondering if any body knows their way around tephra mod software im trying to set up the tune to run a gm 3 bar map sensor and gm iat sensor in speed density
Attachments
96531706-TephraMod-phenem-sd.bin
(256 KiB) Downloaded 62 times

User avatar
Posts: 4861
Joined: Sat Feb 28, 2009 8:38 pm
Location: Wellington NZ

Re: mitsubishi evo 7 tuning tephra mod software

Postby delcowizzid » Tue Oct 23, 2018 9:38 pm

i think this will make it 3 bar but dont hold me to it lol changed the max kpa and load as you will see so it should run in the same table area at 2 bar boost that it would of at 2 bar boost on the 4 bar. as for the gm iat youll want to change the volts vs temp scaling table to suit you can probably grab the shape out of a factory holden bin with tunerpro and add it to the evo table then scale the whole curve until its reading correct
If Its Got Gas Or Ass Count Me In.if it cant be fixed with a hammer you have an electrical problem

User avatar
Posts: 4861
Joined: Sat Feb 28, 2009 8:38 pm
Location: Wellington NZ

Re: mitsubishi evo 7 tuning tephra mod software

Postby delcowizzid » Tue Oct 23, 2018 9:55 pm

That may not actually work its recalibrated the upper kpa area but not down low hmm don't have time right now to fix down low and make the table linier again but you should be able to figure it out
If Its Got Gas Or Ass Count Me In.if it cant be fixed with a hammer you have an electrical problem

Posts: 119
Joined: Mon Dec 07, 2009 2:14 pm

Re: mitsubishi evo 7 tuning tephra mod software

Postby jca » Wed Oct 24, 2018 5:26 am

Thanks delcowizzid ill give it a try today

Posts: 119
Joined: Mon Dec 07, 2009 2:14 pm

Re: mitsubishi evo 7 tuning tephra mod software

Postby jca » Wed Oct 24, 2018 11:37 am

No good delcowizzid map sensor still reads 70kpa with key on engine off the iat reads -59

User avatar
Posts: 4861
Joined: Sat Feb 28, 2009 8:38 pm
Location: Wellington NZ

Re: mitsubishi evo 7 tuning tephra mod software

Postby delcowizzid » Wed Oct 24, 2018 2:28 pm

ok i got the gm 3 bar map scalings from here
https://www.evolutionm.net/forums/ecufl ... tches.html
edited the xml to display the ve map scalings for 3 bar then unedited the xml and pasted the new table coming up with this bin
96531706-TephraMod-phenem-sd new gm 3 bar.bin
(256 KiB) Downloaded 57 times

you will need to edit the xml for your logging software to display actual kpa if i read it right ive opened that many forum posts lol
If Its Got Gas Or Ass Count Me In.if it cant be fixed with a hammer you have an electrical problem

User avatar
Posts: 4861
Joined: Sat Feb 28, 2009 8:38 pm
Location: Wellington NZ

Re: mitsubishi evo 7 tuning tephra mod software

Postby delcowizzid » Wed Oct 24, 2018 2:29 pm

as for iat it should already be setup for gm iat using the old fuel temperature wires
If Its Got Gas Or Ass Count Me In.if it cant be fixed with a hammer you have an electrical problem

Posts: 119
Joined: Mon Dec 07, 2009 2:14 pm

Re: mitsubishi evo 7 tuning tephra mod software

Postby jca » Wed Oct 24, 2018 2:35 pm

Ok i think the owner had wired the sensor in to the old iat sensor wires im just using my genetic scan tool ill have to try find a free scan /loging tool for tractrix cable

User avatar
Posts: 4861
Joined: Sat Feb 28, 2009 8:38 pm
Location: Wellington NZ

Re: mitsubishi evo 7 tuning tephra mod software

Postby delcowizzid » Wed Oct 24, 2018 3:06 pm

You can change it to the air with the click of a button you want me to make one for that
If Its Got Gas Or Ass Count Me In.if it cant be fixed with a hammer you have an electrical problem

User avatar
Posts: 4861
Joined: Sat Feb 28, 2009 8:38 pm
Location: Wellington NZ

Re: mitsubishi evo 7 tuning tephra mod software

Postby delcowizzid » Wed Oct 24, 2018 3:10 pm


then just use sd rpm ve table to dial in fueling back to 14.7 or your target idle and boost fueling by the looks of it
If Its Got Gas Or Ass Count Me In.if it cant be fixed with a hammer you have an electrical problem

Return to Other Tuning

Who is online

Users browsing this forum: No registered users and 2 guests