VS-VY Enhanced Factory Bins

For discussion and distribution of custom code and hacks
User avatar
Posts: 2381
Joined: Fri Mar 14, 2014 8:37 pm
Location: Bacchus Marsh, Vic

Re: The1's Enhanced Factory Bins

Postby Gareth » Thu Jul 14, 2022 10:25 am

charlay86 wrote:Is anyone interested in flex fuel support?


Yes, I am :thumbup:
According to chemistry, alcohol is a solution...

User avatar
Posts: 581
Joined: Thu Sep 17, 2009 2:00 pm
Location: Perth, WA

Re: The1's Enhanced Factory Bins

Postby charlay86 » Fri Jul 15, 2022 11:05 pm

Gareth wrote:
charlay86 wrote:Is anyone interested in flex fuel support?


Yes, I am :thumbup:


Noted.
There seems to be a spare input capture channel available that could be used to read the PWM output signal from a GM flex fuel sensor. :comp:

Posts: 180
Joined: Fri Jul 09, 2010 10:01 pm

Re: The1's Enhanced Factory Bins

Postby 0081 » Sun Jul 17, 2022 11:27 am

charlay86 wrote:
Gareth wrote:
charlay86 wrote:Is anyone interested in flex fuel support?


Yes, I am :thumbup:


Noted.
There seems to be a spare input capture channel available that could be used to read the PWM output signal from a GM flex fuel sensor. :comp:


Flex fuel would be awesome

Posts: 3
Joined: Sat Jun 26, 2021 10:18 pm

Re: The1's Enhanced Factory Bins

Postby twiztidditzwit » Sat Aug 20, 2022 5:56 am

'quipt4it wrote:These are Flash PCM's I believe. No chip to remove/ replace. I think they dub it OBD1.5.
Swapping in an earlier ECM would probably be the go...



What would you suggest to be the best fit for a 95 v6 sfi rwd auto trans?

User avatar
Posts: 581
Joined: Thu Sep 17, 2009 2:00 pm
Location: Perth, WA

Re: The1's Enhanced Factory Bins

Postby charlay86 » Sun Aug 21, 2022 11:36 pm

twiztidditzwit wrote:What would you suggest to be the best fit for a 95 v6 sfi rwd auto trans?


This code is specifically for the Holden 5l V8 and 3.8l 90° V6 motors, with a P6 type PCM. We have real time support on the earlier models that were fitted with a memcal, but not on the later models with flash memory. Real time support is achieved by installing a NVSRAM instead of the memcal eprom.

Your PCM is a very different beast.
I'm somewhat familiar with it as I helped Xnke get his boosted truck working, but I've never actually seen one in the flesh.

Does it still have a location for a memcal header?
If it does, i'd suggest the simplest thing to do would be to remove the flash ic and install the header and try to get hold of an ostrich 2.0.

Posts: 173
Joined: Mon Dec 12, 2016 11:27 am

Re: VS-VY Enhanced Factory Bins

Postby L67PSI » Mon Sep 12, 2022 4:49 pm

Hi guys, I've flashed the VY V6 enhanched code into my VY with a spare PCM using OSE flashtool. Is it possible to adjust the VIN to the correct one? It functions fine, just that it shows the old vehicle VIN.

Thanks

Posts: 3171
Joined: Thu Apr 09, 2009 12:31 pm

Re: VS-VY Enhanced Factory Bins

Postby immortality » Thu Nov 10, 2022 9:38 am

Hi guys,

Is there any way we could add a table for IAT sensor calibration in the V6 tunes?

I think my MAT sensor in the L67 is stuffed (located in the runner for #1 cylinder) and is reading high (yesterday it was pegged over 100°C when it normally sits in the 60°C or less under those driving conditions) so I'm looking to replace it however seeing as the stock GM MAT sensor is old technology and very slow acting I'd like to replace it with something more modern. Was looking at these (which comes with full sensor calibration data).

https://www.motionraceworks.com/product ... -f-52-1248

Posts: 180
Joined: Fri Jul 09, 2010 10:01 pm

Re: VS-VY Enhanced Factory Bins

Postby 0081 » Mon Nov 14, 2022 8:43 am

immortality wrote:Hi guys,

Is there any way we could add a table for IAT sensor calibration in the V6 tunes?

I think my MAT sensor in the L67 is stuffed (located in the runner for #1 cylinder) and is reading high (yesterday it was pegged over 100°C when it normally sits in the 60°C or less under those driving conditions) so I'm looking to replace it however seeing as the stock GM MAT sensor is old technology and very slow acting I'd like to replace it with something more modern. Was looking at these (which comes with full sensor calibration data).

https://www.motionraceworks.com/product ... -f-52-1248


Interesting, fast response is good and it like it may not suffer from heat soak as much.

Posts: 3171
Joined: Thu Apr 09, 2009 12:31 pm

Re: VS-VY Enhanced Factory Bins

Postby immortality » Mon Nov 14, 2022 11:11 am

It would be. What I've noticed with the new sensors is that the sensor tip is a lot longer/further into the runner so it would be reading more accurately rather than been close to the manifold/runner wall which would be more boundary layer air and it doesn't have a cage around it either.

I worked out my sensor is fine and the data logger was reading the MAT sensor wrong although all the other things seemed right. I noticed the memory card had popped out, put it back in, plugged it back in and hey presto numbers are back to normal. I'd still like to swap the MAT sensor out with something more modern though.

User avatar
Posts: 4643
Joined: Mon Jan 04, 2010 10:23 am

Re: VS-VY Enhanced Factory Bins

Postby The1 » Thu Nov 17, 2022 3:16 pm

if it's 0-5volt then it should be ok.

here's the factory sensor calibration table in the out of cal area.
Attachments
intakets.jpg
intakets.jpg (28.26 KiB) Viewed 203 times

PreviousNext

Return to Custom Code

Who is online

Users browsing this forum: No registered users and 1 guest