VS-VY Enhanced Factory Bins
Re: The1's Enhanced Factory Bins
you wont stop spark happening by changing the values, only where it happens. If you want spark cut, then this would have to be codded for and cal tables setup.
- hsv08
- Posts: 547
- Joined: Thu May 09, 2013 6:50 pm
- cars: (EX) VT SENATOR 355 STROKER
(EX) VT SS 304 MANUAL
NOW VX V6 HACK
Re: The1's Enhanced Factory Bins
the red column is your new gs in reference between the old v6 maf and the offset applyed to the v8 maf
I this what you were kind of wanting? the formula would be similiar id imagine
I this what you were kind of wanting? the formula would be similiar id imagine
- Attachments
-
- trial for maf conversion.xlsx
- (23.06 KiB) Downloaded 331 times
Re: The1's Enhanced Factory Bins
kind of, see attached, i want the bottom 2d table interpolated to the top new one, obviously about 100 will be 0 which is fine.
- hsv08
- Posts: 547
- Joined: Thu May 09, 2013 6:50 pm
- cars: (EX) VT SENATOR 355 STROKER
(EX) VT SS 304 MANUAL
NOW VX V6 HACK
Re: The1's Enhanced Factory Bins
ok still not quite sure what you are wanting done.The1 wrote:kind of, see attached, i want the bottom 2d table interpolated to the top new one, obviously about 100 will be 0 which is fine.
are the white values (0.88, 0.91 etc a fixed scale)?
By interpolation i am under the assumption you want the difference of yellow and green added to yellow so you have a interpolated value between the two? ill attach but im not quite sure this is what your after. need a bit more clarification
- Attachments
-
- table conversion.xlsx
- (9.34 KiB) Downloaded 335 times
Re: The1's Enhanced Factory Bins
sorry prob need a better example, say i have 2 tables, the data is in the table with cylair upto 93-593, but i want that data into the 0-850 cylair table, so i need the values calculated and put into the new table.
- Attachments
-
- table conversion.xlsx
- (10.72 KiB) Downloaded 328 times
-
- Posts: 186
- Joined: Fri Jul 09, 2010 10:01 pm
- cars: VY s L67
Haines Hunter - not a car but still a toy
Re: The1's Enhanced Factory Bins
This is what i have come up with so far, not finished yet but if anyone can check if its heading in the right direction.
- Attachments
-
- table conversion-0081.xlsx
- (13.81 KiB) Downloaded 307 times
-
- Posts: 224
- Joined: Wed Oct 08, 2014 11:08 am
- cars: Barina SB C14SE
Lexus RX350
VW Golf Mk5 TDI DSG
Re: The1's Enhanced Factory Bins
Does this make sense? some of the columns align so they are straight copies. the rest are linear interpolations.The1 wrote:sorry prob need a better example, say i have 2 tables, the data is in the table with cylair upto 93-593, but i want that data into the 0-850 cylair table, so i need the values calculated and put into the new table.
Simon
-
- Posts: 186
- Joined: Fri Jul 09, 2010 10:01 pm
- cars: VY s L67
Haines Hunter - not a car but still a toy
Re: The1's Enhanced Factory Bins
If i was one the right track here is my finished one
- Attachments
-
- table conversion-0081-2.xlsx
- (14.34 KiB) Downloaded 320 times
Re: The1's Enhanced Factory Bins
that's correct but i can't see any calculations, youve done it manually?
Re: The1's Enhanced Factory Bins
Yeh yours is on track for what i need, should do the job, my brain hurts with all ive been doing today! So thanks!slewinson wrote:Does this make sense? some of the columns align so they are straight copies. the rest are linear interpolations.The1 wrote:sorry prob need a better example, say i have 2 tables, the data is in the table with cylair upto 93-593, but i want that data into the 0-850 cylair table, so i need the values calculated and put into the new table.
Simon