VS-VY Enhanced Factory Bins
Re: The1's Enhanced Factory Bins
what settings have you got, the below should work.
- Attachments
-
- egr.JPG (71.75 KiB) Viewed 6965 times
- delcowizzid
- Posts: 5493
- Joined: Sat Feb 28, 2009 8:38 pm
- Location: Wellington NZ
- Contact:
Re: The1's Enhanced Factory Bins
I never changed the one labelled coolant check I'll reflash today and see what happens 100% egr going up hill at 80kmh sucks lol
If Its Got Gas Or Ass Count Me In.if it cant be fixed with a hammer you have an electrical problem
Re: The1's Enhanced Factory Bins
yeh factory ones at 5c so wont enable the coolant check.
- Holden202T
- Posts: 10311
- Joined: Sat Feb 28, 2009 9:05 pm
- Location: Tenambit, NSW
- Contact:
Re: The1's Enhanced Factory Bins
ahh yeah that would do it!
No matter what the question is, the answer is always more horsepower!
Just starting out? Have a read of the getting started guide
Basic tuning of a delco ECM with $12P thread
Advanced tuning of a delco ECM with $12P thread
Just starting out? Have a read of the getting started guide
Basic tuning of a delco ECM with $12P thread
Advanced tuning of a delco ECM with $12P thread
- delcowizzid
- Posts: 5493
- Joined: Sat Feb 28, 2009 8:38 pm
- Location: Wellington NZ
- Contact:
Re: The1's Enhanced Factory Bins
Ok startup coolant check temp has sorted it she doesn't activate now thanks now to find some down low power it feels like torque reduction active at low revs then it just pulls like a train might be time to fit the wideband and force open loop for some fueling checks.especially after I gut the cat tomorrow lol
If Its Got Gas Or Ass Count Me In.if it cant be fixed with a hammer you have an electrical problem
- Holden202T
- Posts: 10311
- Joined: Sat Feb 28, 2009 9:05 pm
- Location: Tenambit, NSW
- Contact:
Re: The1's Enhanced Factory Bins
needs more timing down low ?
No matter what the question is, the answer is always more horsepower!
Just starting out? Have a read of the getting started guide
Basic tuning of a delco ECM with $12P thread
Advanced tuning of a delco ECM with $12P thread
Just starting out? Have a read of the getting started guide
Basic tuning of a delco ECM with $12P thread
Advanced tuning of a delco ECM with $12P thread
Re: The1's Enhanced Factory Bins
Vx flash usually has plenty of spark, check for retard
- delcowizzid
- Posts: 5493
- Joined: Sat Feb 28, 2009 8:38 pm
- Location: Wellington NZ
- Contact:
Re: The1's Enhanced Factory Bins
Could be nearly 500k km of timing chain stretch lol.its never been sharp or responsive my mates vy eco had a lot more down low and it was a high km taxi I'll shove the wideband up it and see where I'm at
If Its Got Gas Or Ass Count Me In.if it cant be fixed with a hammer you have an electrical problem
Re: The1's Enhanced Factory Bins
Did you lower the pe cutin it's like 60% TPS from factory
- JA2Z
- Posts: 76
- Joined: Tue Mar 08, 2016 9:59 am
- cars: - WH II 5.7L Statesman (daily)
- VT 5.0L Calais
- 1994 Ford Probe V6 DOHC
- 2007 Ford Focus TDCI 2.0 - Location: East Gippsland, Victoria
- Contact:
Re: The1's Enhanced Factory Bins
Hi Mate,
I went to update the bin from 0.91 Enhanced to 1.00 to enable the WIDEBAND and MAP A5/B10 input support, it failed, and now I've lost comms to the NVRAM - I can't get hardware to detect anymore and no vehicle start even though it does crank.
Can I attempt to use OSE flash tool to upload the bin if I have no emulation hardware detected in Tuner Pro?
and if so, what options to I select, because VT V8 isn't listed in the drop-down box.
I tried my old cheap USB ALDL interface just to check, but still no dice.
Tried the Factory memcal, but I have no BCM, so not even a crank attempt.
If I didn't have "No hardware detected" I would just suspect I'd run out of fuel, but it won't start right after a unsuccessful bin write.
Any help would be appreciated.
I went to update the bin from 0.91 Enhanced to 1.00 to enable the WIDEBAND and MAP A5/B10 input support, it failed, and now I've lost comms to the NVRAM - I can't get hardware to detect anymore and no vehicle start even though it does crank.
Can I attempt to use OSE flash tool to upload the bin if I have no emulation hardware detected in Tuner Pro?
and if so, what options to I select, because VT V8 isn't listed in the drop-down box.
I tried my old cheap USB ALDL interface just to check, but still no dice.
Tried the Factory memcal, but I have no BCM, so not even a crank attempt.
If I didn't have "No hardware detected" I would just suspect I'd run out of fuel, but it won't start right after a unsuccessful bin write.
Any help would be appreciated.