The1's Enhanced Factory Bins

For discussion and distribution of custom code and hacks
Posts: 510
Joined: Mon Jul 11, 2016 6:29 am

Re: The1's Enhanced Factory Bins

Postby Wade » Wed May 09, 2018 8:15 pm

The1 can you plz explain the function of the supercharger boost valve tables in your l67 enhanced bins

User avatar
Posts: 4087
Joined: Mon Jan 04, 2010 10:23 am

Re: The1's Enhanced Factory Bins

Postby The1 » Wed May 09, 2018 8:37 pm

it will control the factory boost valve

Posts: 510
Joined: Mon Jul 11, 2016 6:29 am

Re: The1's Enhanced Factory Bins

Postby Wade » Tue May 22, 2018 2:41 am

In the enhanced xdf is there a way to add crank angle. I can see spark angle and angle reference. What im trying to do and work out, is how to set things up so i can create a new history table that allows me to see knock based off crank angle.

User avatar
Posts: 9617
Joined: Sat Feb 28, 2009 9:05 pm
Location: Tenambit, NSW

Re: The1's Enhanced Factory Bins

Postby Holden202T » Tue May 22, 2018 1:12 pm

I don't understand, the crank angle will be whatever the timing number is, before TDC for that throw of the crank ?

eg. if you have 16 degrees of timing then that will be 16 degrees before the piston gets to top dead centre.....

the reference angle is only used so the computer knows how to offset the timing for the location of the crank angle sensor in relation to TDC.

Posts: 510
Joined: Mon Jul 11, 2016 6:29 am

Re: The1's Enhanced Factory Bins

Postby Wade » Tue May 22, 2018 4:40 pm


Posts: 510
Joined: Mon Jul 11, 2016 6:29 am

Re: The1's Enhanced Factory Bins

Postby Wade » Tue May 22, 2018 4:43 pm

Trying to figure out if it’s possible to look at knock vs crank angle would further determine if the knocks false or not. Or is that not possible with enhanced?

User avatar
Posts: 4773
Joined: Sat Feb 28, 2009 8:38 pm
Location: Wellington NZ

Re: The1's Enhanced Factory Bins

Postby delcowizzid » Tue May 22, 2018 7:25 pm

You need a pressure transducer in the cylinder and an accurate way to measure crank angle to do what you are trying to do .there is equipment to do it but it's pricy high end gear so you can change timing till cylinder pressure hits at the perfect angle.just get on a dyno dump and tune it till you don't gain anything
If Its Got Gas Or Ass Count Me In.if it cant be fixed with a hammer you have an electrical problem

Posts: 510
Joined: Mon Jul 11, 2016 6:29 am

Re: The1's Enhanced Factory Bins

Postby Wade » Tue May 22, 2018 7:43 pm

Ah ok. Cheers

User avatar
Posts: 147
Joined: Mon Nov 09, 2009 4:56 pm
Location: Perth

Re: The1's Enhanced Factory Bins

Postby madmaxisback » Tue May 22, 2018 7:46 pm

Or drop $1500 on one for these https://www.plex-tuning.com/products/pl ... k-monitor/
Wishing. :cash:

I made up home brew version but would love one of these too!

User avatar
Posts: 149
Joined: Tue Dec 17, 2013 1:05 am

Re: The1's Enhanced Factory Bins

Postby Ken » Sun Jun 17, 2018 12:51 am

The1 wrote:depending on bus chatter ive still been able to reflash a pcm with vats on. Failing that it would need a eeprom desoldered and reflashed and soldered back in. But for the cost of the pcm's, ive picked some up for $15 each it's just easier to grab another.

Is there a reason you desolder, reflash and solder back in, as opposed to soldering a chip mount on the board and just press the chip into the mount.
Are the chip mounts a problem, is why I ask.

PreviousNext

Return to Custom Code

Who is online

Users browsing this forum: No registered users and 2 guests