How do I get 12P to go into closed loop mode
- Holden202T
- Posts: 10311
- Joined: Sat Feb 28, 2009 9:05 pm
- Location: Tenambit, NSW
- Contact:
Re: How do I get 12P to go into closed loop mode
take note of injector duty cycle too ... got any logs ?
No matter what the question is, the answer is always more horsepower!
Just starting out? Have a read of the getting started guide
Basic tuning of a delco ECM with $12P thread
Advanced tuning of a delco ECM with $12P thread
Just starting out? Have a read of the getting started guide
Basic tuning of a delco ECM with $12P thread
Advanced tuning of a delco ECM with $12P thread
-
- Posts: 1833
- Joined: Sat Aug 06, 2011 7:58 am
- cars: V8 VR Commodore BT1
LB Lancer 2L turbo & Delco
Starion TBI with Delco
Mitsubishi Lancer EVO4 track car
NA MX5
3 vintage motor bikes - Location: Padstow NSW
Re: How do I get 12P to go into closed loop mode
This is the last log I have taken
- Attachments
-
- t13-8-13.xdl
- (320.3 KiB) Downloaded 441 times
- VL400
- Posts: 4991
- Joined: Sun Mar 01, 2009 2:54 pm
- cars: VL Calais and Toyota Landcruiser. Plus some toys :)
- Location: Perth, WA
- Contact:
Re: How do I get 12P to go into closed loop mode
From just a quick look (will check it out better later) it looks like you in single fire mode which wont be helping.
Have a look at what you have set for..
"Run A/F Param - Minimum BPW for sync double fire fuel delivery (Min Value)" - set it to 0
"Run A/F Param - Minimum BPW for sync double fire fuel delivery (Upper Value)" - set it to 0
"Map A: set=Single fire option, clear=Double fire option" - Clear the flag
Have a look at what you have set for..
"Run A/F Param - Minimum BPW for sync double fire fuel delivery (Min Value)" - set it to 0
"Run A/F Param - Minimum BPW for sync double fire fuel delivery (Upper Value)" - set it to 0
"Map A: set=Single fire option, clear=Double fire option" - Clear the flag
- delcowizzid
- Posts: 5493
- Joined: Sat Feb 28, 2009 8:38 pm
- Location: Wellington NZ
- Contact:
Re: How do I get 12P to go into closed loop mode
jesus its lean on boost 18:1
If Its Got Gas Or Ass Count Me In.if it cant be fixed with a hammer you have an electrical problem
- delcowizzid
- Posts: 5493
- Joined: Sat Feb 28, 2009 8:38 pm
- Location: Wellington NZ
- Contact:
Re: How do I get 12P to go into closed loop mode
its also not displaying a 4 cylinder memcal in the aldl
If Its Got Gas Or Ass Count Me In.if it cant be fixed with a hammer you have an electrical problem
-
- Posts: 1833
- Joined: Sat Aug 06, 2011 7:58 am
- cars: V8 VR Commodore BT1
LB Lancer 2L turbo & Delco
Starion TBI with Delco
Mitsubishi Lancer EVO4 track car
NA MX5
3 vintage motor bikes - Location: Padstow NSW
Re: How do I get 12P to go into closed loop mode
Thanks I will have a look tomorrow. If I set the values to double fire will it affect my VE values or will they be the same? It should show 4cyl but I will investigate. I think the 18:1 is not correct due to the missfire and obvious lean mixture reading.
-
- Posts: 1833
- Joined: Sat Aug 06, 2011 7:58 am
- cars: V8 VR Commodore BT1
LB Lancer 2L turbo & Delco
Starion TBI with Delco
Mitsubishi Lancer EVO4 track car
NA MX5
3 vintage motor bikes - Location: Padstow NSW
Re: How do I get 12P to go into closed loop mode
I had a look and have changed to double fire but can't find how I set to 4cyl memcal? I have it set to 4cyl so do I have to change anything else?
- VL400
- Posts: 4991
- Joined: Sun Mar 01, 2009 2:54 pm
- cars: VL Calais and Toyota Landcruiser. Plus some toys :)
- Location: Perth, WA
- Contact:
Re: How do I get 12P to go into closed loop mode
Its the actual physical memcal that is currently not 4 cyl - its using TBI mode currently so will run very lean if you just change that to 4 cyl. In saying that though, you have fluked it as having it set to TBI mode and single fire it will inject the same amount of fuel as 4 cyl in double fire.
If your running a modded memcal then these are how to select the different types .. http://pcmhacking.net/forums/viewtopic. ... t=10#p6850
If your running a modded memcal then these are how to select the different types .. http://pcmhacking.net/forums/viewtopic. ... t=10#p6850
-
- Posts: 1833
- Joined: Sat Aug 06, 2011 7:58 am
- cars: V8 VR Commodore BT1
LB Lancer 2L turbo & Delco
Starion TBI with Delco
Mitsubishi Lancer EVO4 track car
NA MX5
3 vintage motor bikes - Location: Padstow NSW
Re: How do I get 12P to go into closed loop mode
Thanks for bringing that to my attention. I went through my eprom collection and found a 1.8 multipoint Camira and set it up with the 27sf512 and knock board and started again. I can now see 4cyl memcal and found I had to reset the injector flow rate and richen the VE tables to get it back to near the same wideband figures it had before but all going great now. I'll have to take it for a drive a make a new log.
-
- Posts: 1833
- Joined: Sat Aug 06, 2011 7:58 am
- cars: V8 VR Commodore BT1
LB Lancer 2L turbo & Delco
Starion TBI with Delco
Mitsubishi Lancer EVO4 track car
NA MX5
3 vintage motor bikes - Location: Padstow NSW
Re: How do I get 12P to go into closed loop mode
I have looked at the memcal resistor diagram and if I cut the legs and fit the two resistors as shown in the diagram will it them work as a 4cyl memcal? and if so will limp mode work? The reason I ask is I have 4 other tbi memcals I would like to convert. Funny that I picked 2 mecals out of the bag without knowing this and they are both tbi.