OSE 12P V112

For discussion and distribution of custom code and hacks
User avatar
VL400
Posts: 4991
Joined: Sun Mar 01, 2009 2:54 pm
cars: VL Calais and Toyota Landcruiser. Plus some toys :)
Location: Perth, WA
Contact:

Re: OSE 12P V111

Post by VL400 »

Let me have a look and see what can be done and get back to you.

There are only two 0-5V analog inputs, one is the wideband and the other will need a hardware mod to use it with a MAP sensor.
stevedarman
Posts: 109
Joined: Sat Mar 21, 2009 8:59 am
cars: VX commodore

Re: OSE 12P V111

Post by stevedarman »

Cool I will wait to see how you go
stevedarman
Posts: 109
Joined: Sat Mar 21, 2009 8:59 am
cars: VX commodore

Re: OSE 12P V111

Post by stevedarman »

Hi VL 400,
Have you had a chance to see if a second map can be added for baro calibration
User avatar
VL400
Posts: 4991
Joined: Sun Mar 01, 2009 2:54 pm
cars: VL Calais and Toyota Landcruiser. Plus some toys :)
Location: Perth, WA
Contact:

Re: OSE 12P V111

Post by VL400 »

I have looked at it and it is possible, but it means using either the wideband input or requiring a hardware change to use the universal analog input. Its on the the list to add but as there is no one other than yourself requesting this, along with the drawbacks, it is low on the list.

If you want it added to a custom release PM me.
User avatar
VL400
Posts: 4991
Joined: Sun Mar 01, 2009 2:54 pm
cars: VL Calais and Toyota Landcruiser. Plus some toys :)
Location: Perth, WA
Contact:

Re: OSE 12P V112

Post by VL400 »

Have released 12P V112, the zip is in the first post of this thread. Flashtool V1.49 also released and adds support for this version.

The following code changes from V1.11 have been made...
- Added basic VT/VY Cluster Support. Use the Flashtool V1.49 or later and the ALDL Editor to setup
- Added Option to Always Use Default/Calculated MAP for experimental Alpha-N
- Force Open Loop Option
- Modified Boost Multiplier. Was previously only 100-200% for both 2 and 3 bar sensors
Auto selection for 2/3 bar MAP sensor to have 100-200% or 100-300% based on sensor type
- Added ignition dwell items to cal
- Added Code 48 for high boost pressure. Code 48 can optionally be used for over boost fuel cut.
- Added option to use dedicated baro sensor on pin b12. Code 32 added for fault detection

ALDL Changes
- Changed the injector PW term to one that does not change with single/double fire. The injector duty cycle calc works for both modes. NOTE: single fire is limited to 50% even though it reports higher when logged, this is hardware limited!
kojab
Posts: 440
Joined: Sun Mar 22, 2009 11:52 am
cars: VT V6 supercharged in a corolla
Location: Sydney
Contact:

Re: OSE 12P V112

Post by kojab »

Another great release no doubt. Thank you VL400 for all these extra features. Looking forward to trying the new dwell items on my 3SGTE powered AW11 MR2.
VX L67 Getrag
Posts: 2877
Joined: Sun Aug 02, 2009 9:16 pm
Location: Bayside, Melbourne, Victoria
Contact:

Re: OSE 12P V112

Post by VX L67 Getrag »

UM I just downloaded it mainly for the latest version of the flashtool, but it doesn't seem to be in there?

EDIT; Don't worry I just realized it's not in the zip, it's downloaded separate!
User avatar
vlad01
Posts: 7780
Joined: Mon Oct 08, 2012 6:41 pm
cars: VP I S
VP I executive
VP II executive
VP II executive #2
VR II executive
Location: Kyneton, Vic

Re: OSE 12P V112

Post by vlad01 »

do i migrate v111 to v112 using the flash tool?
I'm the director of VSH (Vlad's Spec Holden), because HSV were doing it ass about.
User avatar
VL400
Posts: 4991
Joined: Sun Mar 01, 2009 2:54 pm
cars: VL Calais and Toyota Landcruiser. Plus some toys :)
Location: Perth, WA
Contact:

Re: OSE 12P V112

Post by VL400 »

kojab wrote:Looking forward to trying the new dwell items on my 3SGTE powered AW11 MR2.
A perfect case of needing this! It still uses the normal Delco multi slope dwell, it just gives access to the items used.
vlad01 wrote:do i migrate v111 to v112 using the flash tool?
Yep. Process is basically get the current cal from your car, migrate it using the tool in the binary functions menu. Write one of the V112 bins to the ECU using write bin. When finished write your migrated cal.
Also spent ages getting the MAP scaling with baro working properly, the ADX I sent you was not correct at low loads. The v112 ADXs should be correct.
Dylan
Posts: 3355
Joined: Mon Aug 02, 2010 6:35 pm
cars: VR Commodore V8

Re: OSE 12P V112

Post by Dylan »

Good work mate thanks for your effort!!
Post Reply