OSE 12P V112

For discussion and distribution of custom code and hacks
Posts: 15
Joined: Wed Nov 23, 2011 7:32 am
Location: SE USA

Re: OSE 12P V112

Postby DixiePicker » Sun Feb 02, 2020 2:53 am

Added functions to ADX for $12P that may be of use. Downloaded the ADX file from zip. Added Mode 4 functions and additional Dash. Verified in vehicle except the TCC command which I don't use. Dash is Black background for sunlight. Not using NVRAM.


Site Admin
User avatar
Posts: 6562
Joined: Sat Feb 28, 2009 8:34 pm

Re: OSE 12P V112

Postby antus » Sun Feb 02, 2020 6:34 pm

Thanks for that! Ive put a link to your post from the first post in this thread so people can find it.
Have you read the FAQ? For lots of information and links to significant threads see here: viewtopic.php?f=7&t=1396

Posts: 163
Joined: Tue Oct 16, 2012 12:17 pm
Location: Perth

Re: OSE 12P V112

Postby Tre-Cool » Sun Sep 06, 2020 8:21 pm

I must be going blind, but what the F is the injector scaling table or map called?

I cannot see it in Tunerpro.

Found it. not an obvious name i was looking for
Last edited by Tre-Cool on Sun Sep 06, 2020 8:29 pm, edited 1 time in total.

User avatar
Posts: 6882
Joined: Mon Oct 08, 2012 6:41 pm
Location: Kyneton, Vic

Re: OSE 12P V112

Postby vlad01 » Sun Sep 06, 2020 8:24 pm

what do you mean by injector scaling?
I'm the director of VSH (Vlad's Spec Holden), because HSV were doing it ass about.

Posts: 163
Joined: Tue Oct 16, 2012 12:17 pm
Location: Perth

Re: OSE 12P V112

Postby Tre-Cool » Sun Sep 06, 2020 8:33 pm

was expecting to see a table to modify the injector flow rate vs manifold pressure or the likes.

Looks like it's a single value which makes sense since these were all vac referenced anyway.

This car is a bit of an unknown, looks to have some red top injectors on it, so looking for the magic number to plug to atleast get the fueling close. It's pretty rich on the base 12p tune file.

User avatar
Posts: 6882
Joined: Mon Oct 08, 2012 6:41 pm
Location: Kyneton, Vic

Re: OSE 12P V112

Postby vlad01 » Sun Sep 06, 2020 9:02 pm

The only stuff for injectors is the base flow scalar, voltage offset table, adders for the voltage offsets and cranking pulses and few other minor settings.

The VE table basically tells how much fuel to inject for the most part.
I'm the director of VSH (Vlad's Spec Holden), because HSV were doing it ass about.

Posts: 163
Joined: Tue Oct 16, 2012 12:17 pm
Location: Perth

Re: OSE 12P V112

Postby Tre-Cool » Mon Sep 07, 2020 12:50 pm

anyone used the aem x-series widebands and fed it into the ecu? I predominantly use them for tuning all my LS stuff through my efilive cable so it has the signal & gnd wire to correct any gnd offsets. If I dont plug it in the signal afr is up the shit.

So i suspect if i plug the 0-5v signal into the ecu i might suffer the offset issue too.

Site Admin
User avatar
Posts: 6562
Joined: Sat Feb 28, 2009 8:34 pm

Re: OSE 12P V112

Postby antus » Mon Sep 07, 2020 4:00 pm

The main injector rate is "Run A/F Param - Displacement/inj flow rate (Litres/Grams per sec)" use ctrl + f and search for a scaler with inj
There is also "Injector - Injector Opening Time vs Battery Voltage" and "Injector - Injector bias add-on vs Injector pulse width for non-linear operating region" as tables.

I believe delcowizid is using aem, though Im not sure what model. I wouldnt expect offset problems with 12p, it was some of the later PCMs that had the resistor to remove.
Have you read the FAQ? For lots of information and links to significant threads see here: viewtopic.php?f=7&t=1396

User avatar
Posts: 6882
Joined: Mon Oct 08, 2012 6:41 pm
Location: Kyneton, Vic

Re: OSE 12P V112

Postby vlad01 » Mon Sep 07, 2020 6:22 pm

808 has the resistor but you don't need to remove it, just adjust the 0v and 5V values slightly to correct it. Mine were like 10.2 for 0v and 19.9 or something for 5v. Each WB will be different so just key on/off to run the sequencer and adjust as needed.
I'm the director of VSH (Vlad's Spec Holden), because HSV were doing it ass about.

Posts: 163
Joined: Tue Oct 16, 2012 12:17 pm
Location: Perth

Re: OSE 12P V112

Postby Tre-Cool » Mon Sep 07, 2020 11:56 pm

i ended up just eye-balling it off the dyno wideband & in-car unit.

this was for a mates 355 stroker, turbo 400 and stall so it sucked for power. stock banana manifold and intake and made 260whp.

I looked up the injector part number (red tops -310cc) VE seems rather low at 45% at wot & 55% injector duty cycle, a lot more parameters to play with, but for a quick couple hours of screwing around on the dyno he was happy to replace the old kalmaker tune that was in it.

PreviousNext

Return to Custom Code

Who is online

Users browsing this forum: No registered users and 1 guest