Real Time Modded Factory Bins

For discussion and distribution of custom code and hacks
User avatar
antus
Site Admin
Posts: 8228
Joined: Sat Feb 28, 2009 8:34 pm
cars: TX Gemini 2L Twincam
TX Gemini SR20 18psi
Datsun 1200 Ute
Subaru Blitzen '06 EZ30 4th gen, 3.0R Spec B
Contact:

Re: Real Time Modded Factory Bins

Post by antus »

If I recall correctly I think you need a mod to the bin to stop the ecu checking the feedback and treating it as an error when its not b+?

What bin are you trying?
Have you read the FAQ? For lots of information and links to significant threads see here: http://pcmhacking.net/forums/viewtopic.php?f=7&t=1396
User avatar
VL400
Posts: 4991
Joined: Sun Mar 01, 2009 2:54 pm
cars: VL Calais and Toyota Landcruiser. Plus some toys :)
Location: Perth, WA
Contact:

Re: Real Time Modded Factory Bins

Post by VL400 »

On a VS ecotec you shouldnt need to mod the bin, the factory fault handling should take care of it and substitute battery voltage for the injector monitor voltage when it detects a fault - I think holden202 had it setup and working well on his Torana. But, you must leave the fault handling on otherwise it will chuck a heap of fuel in from what it thinks is a 0-5v injector feedback signal. Can mask the CEL but leave fault processing on for code 57.
User avatar
The1
Posts: 4694
Joined: Mon Jan 04, 2010 10:23 am

Re: Real Time Modded Factory Bins

Post by The1 »

arh my bad, will try again with fault ON and fault masked.
User avatar
Holden202T
Posts: 10308
Joined: Sat Feb 28, 2009 9:05 pm
Location: Tenambit, NSW
Contact:

Re: Real Time Modded Factory Bins

Post by Holden202T »

if you have no luck with that i can send you my bin i used and see if that fixes it.
User avatar
The1
Posts: 4694
Joined: Mon Jan 04, 2010 10:23 am

Re: Real Time Modded Factory Bins

Post by The1 »

it's workin fine now guys thanks with the MALF ON
User avatar
Holden202T
Posts: 10308
Joined: Sat Feb 28, 2009 9:05 pm
Location: Tenambit, NSW
Contact:

Re: Real Time Modded Factory Bins

Post by Holden202T »

good to know!
User avatar
The1
Posts: 4694
Joined: Mon Jan 04, 2010 10:23 am

Re: Real Time Modded Factory Bins

Post by The1 »

i wont how hard a modded bin would be to implement so you can use pin B10, i have seen this used a kal bin i think for map sensor input, would make it nice then not having a fault logged all the time and be able to leave the wiring alone, would this already be enabled perhaps and just need to find the right output in the adx? no big issue though just a thought.
User avatar
VL400
Posts: 4991
Joined: Sun Mar 01, 2009 2:54 pm
cars: VL Calais and Toyota Landcruiser. Plus some toys :)
Location: Perth, WA
Contact:

Re: Real Time Modded Factory Bins

Post by VL400 »

There is an analog chan that gets read and looks like it was maybe for a baro sensor. Not sure what pin number it is going to though, but the raw value gets shoved in the mode 1 msg 0 datastream at offset 58. Might be able to test B10 with a 0-5v signal but I would initially use a 10k resistor so nothing gets damaged.
User avatar
The1
Posts: 4694
Joined: Mon Jan 04, 2010 10:23 am

Re: Real Time Modded Factory Bins

Post by The1 »

thanks VL , ill have a tinker at some point, i tried reading a dissasembled bin but ive never done anything with assembly lang before :(
User avatar
DieselBob
Posts: 164
Joined: Sun Mar 28, 2010 5:43 pm
cars: Vr SII Ute
Location: Brisbane QLD

Re: Real Time Modded Factory Bins

Post by DieselBob »

Wasn't sure where to put this figured here was as good as any with the Innovate stuff scattered through....
I've done limited testing so let me know if theres problems and I'll fix...
Innovate_TunerPro_O2-ConversionCalculation.xls
(30.5 KiB) Downloaded 689 times
Post Reply