Open and closed loop vn v6

General Tuning Questions And Discussions
Post Reply
Shed racer 26
Posts: 2
Joined: Thu Mar 14, 2019 3:06 pm
cars: Holden vx v6 vn v6

Open and closed loop vn v6

Post by Shed racer 26 »

Hi iam new on here thank in advane for any information 1,does the knock sensor work in open loop? 2, does the delco 808 go in open loop at WOT .3 if the knock sensor is not workings how much will the ecu advance the ignition timing.4,in open loop what would the preset air fuel ratio be. All the above is on vn v6 Thanks again
User avatar
delcowizzid
Posts: 5493
Joined: Sat Feb 28, 2009 8:38 pm
Location: Wellington NZ
Contact:

Re: Open and closed loop vn v6

Post by delcowizzid »

The knock sensor works up to around 3600rpm then turns off . If it's broken or unplugged the ecu will pull 10 degrees of timing out everywhere .as for air fuel spends on the tune s1 and 2 are different so are many of the revisions and if you change anything on the car airflow related ie intake or headers or exhaust it will still inject the same amount of fuel it always has so could have any manor of fuel ratios over the intire rpm range .download tunerpro turtles and some bin files out of the stock Holden bin file thread in the Holden aldl ecus section and the matching xdfs out of the stock Holden xdf thread
If Its Got Gas Or Ass Count Me In.if it cant be fixed with a hammer you have an electrical problem
Shed racer 26
Posts: 2
Joined: Thu Mar 14, 2019 3:06 pm
cars: Holden vx v6 vn v6

Re: Open and closed loop vn v6

Post by Shed racer 26 »

Thank you that's been great do you know if the ecu on vn v6 goes into open loop at wide open throttle and also what is max spark advance
User avatar
antus
Site Admin
Posts: 8237
Joined: Sat Feb 28, 2009 8:34 pm
cars: TX Gemini 2L Twincam
TX Gemini SR20 18psi
Datsun 1200 Ute
Subaru Blitzen '06 EZ30 4th gen, 3.0R Spec B
Contact:

Re: Open and closed loop vn v6

Post by antus »

Max spark advance is a configurable item, generally around 45 degrees by default, but set it to what you need/want.
Have you read the FAQ? For lots of information and links to significant threads see here: http://pcmhacking.net/forums/viewtopic.php?f=7&t=1396
User avatar
delcowizzid
Posts: 5493
Joined: Sat Feb 28, 2009 8:38 pm
Location: Wellington NZ
Contact:

Re: Open and closed loop vn v6

Post by delcowizzid »

Yep open loop when load gets above 70kpa all the way to full throttle timing is different in every tune they don't need anymore than 28 degrees up top at full throttle
If Its Got Gas Or Ass Count Me In.if it cant be fixed with a hammer you have an electrical problem
pman92
Posts: 464
Joined: Thu May 03, 2012 10:50 pm
cars: HZ One Tonner
VE Ute
Location: Castlemaine, Vic

Re: Open and closed loop vn v6

Post by pman92 »

"Open loop" you are referring to (oxygen sensor to trim fuel) is unrelated to ignition.

There are many different "closed loop" systems as part of the engine management:

-Oxygen sensor as feedback about fuel delivery is one closed loop system. (If the sensor says rich or lean, fuel will be added or deducted as required)

-Knock sensor for feedback about ignition advance is another closed loop system. (If knock is detected advance will be reduced)

-Engine speed as feedback for idle speed control is another closed loop system. (IAC or Ignition advance will be used to maintain the desired idle speed).

The closed loop fuel system will be open loop whenever the desired AFR is not lambda 1.000. (Full throttle will be rich, so it will be open loop). It will also be open loop when other parameters in the particular tune are not met (coolant temp, run time, etc).
VR-VY Holden BCM Simulator: View Post
MrModule.com.au
Post Reply