VR with l67 help needed

General Tuning Questions And Discussions
Posts: 118
Joined: Wed May 19, 2010 2:21 pm

VR with l67 help needed

Postby vp304 » Fri Jun 19, 2020 11:55 pm

Hey guys long time i havnt been on here for.
Used to run a vp 5l turbo running on 12p with a vl400 i think hi speed coms board and using a moates ostrich 1.0

Now bought another project car a running vr ute v6 with 4l60e

Have bought a vt super 6 wreck and hoping to transplant the l67 into the vr.
Have done a heap of googling etc.
Going to keep the vr 4l60 and use the vr engine loom

My question is looks like im going to have to use 11p
Does anyone have a similar setup on a vr auto. Hoping to find a tune that can get me going then i can just street tune fine tune the fuel side on the street with my wideband.


Tune can be close to standard as ute will be a workhorse tow vehicle etc bit of fun.

To tune the vr will i be able to use my moates ostrich 1 ? Sorry been a long time since i used it last etc. Still have tuner pro etc on my pc and laptop

Any help will be appreciated
thanks

User avatar
Posts: 5266
Joined: Sat Feb 28, 2009 8:38 pm
Location: Wellington NZ

Re: VR with l67 help needed

Postby delcowizzid » Sat Jun 20, 2020 1:16 am

Yeah ostrich and aldl cable for logging.
If Its Got Gas Or Ass Count Me In.if it cant be fixed with a hammer you have an electrical problem

Posts: 118
Joined: Wed May 19, 2010 2:21 pm

Re: VR with l67 help needed

Postby vp304 » Sat Jun 20, 2020 8:43 am

Hey delcowizzid
So for real time tuning on vr auto ecu i will have to purchase something like this
viewtopic.php?f=14&t=3612

Now to just find a tune :)

Sorry about all the questions has just been 7 plus years since i played with this stuff a lot has gone a blur

User avatar
Posts: 5266
Joined: Sat Feb 28, 2009 8:38 pm
Location: Wellington NZ

Re: VR with l67 help needed

Postby delcowizzid » Sat Jun 20, 2020 11:27 am

That board or your ostrich can real-time tune. And then cable for aldl logging or tuning with the nvram board viewtopic.php?f=14&t=3616
If Its Got Gas Or Ass Count Me In.if it cant be fixed with a hammer you have an electrical problem

Posts: 118
Joined: Wed May 19, 2010 2:21 pm

Re: VR with l67 help needed

Postby vp304 » Sat Jun 20, 2020 3:41 pm

delcowizzid
thanks again for the help
Whats my chances of finding a tune already

Or will i have to start with a 11p vr auto v6 tune in 2 bar
put super 6 timing maps and fuel maps and injector data and go from there ?

User avatar
Posts: 9984
Joined: Sat Feb 28, 2009 9:05 pm
Location: Tenambit, NSW

Re: VR with l67 help needed

Postby Holden202T » Mon Jun 22, 2020 11:29 am

wouldnt you be better off using the super 6 gearbox ?

Posts: 118
Joined: Wed May 19, 2010 2:21 pm

Re: VR with l67 help needed

Postby vp304 » Mon Jun 22, 2020 2:27 pm

By what i have read on the net
Cant use super 6 trans as different to vr wiring side
Easier to bolt up motor and use vr wiring and vr auto trans on super 6 motor

User avatar
Posts: 9984
Joined: Sat Feb 28, 2009 9:05 pm
Location: Tenambit, NSW

Re: VR with l67 help needed

Postby Holden202T » Mon Jun 22, 2020 3:09 pm

isnt that just the module on the side of the box ? which you shouldn't need ? as long as the round plug that goes into the box is the same it should work ?

Posts: 118
Joined: Wed May 19, 2010 2:21 pm

Re: VR with l67 help needed

Postby vp304 » Mon Jun 22, 2020 11:57 pm

No idea holden202T about the electrical side of the box.
But wouldnt the only benefit of the vt super 6 box be that its probably 1% stronger than my current vr 4l60e ?

Found another guy on here that done the mechanical side of the swap on a vr ute and he used vr 4l60e to l67 motor.
i pm him and he said he didnt do the tune was done by a shop with kalmaker

Posts: 118
Joined: Wed May 19, 2010 2:21 pm

Re: VR with l67 help needed

Postby vp304 » Fri Jun 26, 2020 1:11 pm

Anyone ?

Next

Return to General Tuning Discussion

Who is online

Users browsing this forum: No registered users and 2 guests