VR with l67 help needed

General Tuning Questions And Discussions
vp304
Posts: 451
Joined: Wed May 19, 2010 2:21 pm

Re: VR with l67 help needed

Post by vp304 »

Ok so what should i do delcowizzid?
VX L67 Getrag
Posts: 2877
Joined: Sun Aug 02, 2009 9:16 pm
Location: Bayside, Melbourne, Victoria
Contact:

Re: VR with l67 help needed

Post by VX L67 Getrag »

I'm pretty sure in the $11p package there was a start tune for L67 as I had done one with VS L67 & the VS L67 box behind it.
vp304
Posts: 451
Joined: Wed May 19, 2010 2:21 pm

Re: VR with l67 help needed

Post by vp304 »

Vx L67 getrag
Mines in a vr with complete L67 motor and using vr 4l60e and vr ecu

If that tune you talk about exists can I copy the timing maps and fuel settings and ve table to get me going?
Or cause it's vs and uses a maf it's gonna be out also?
VX L67 Getrag
Posts: 2877
Joined: Sun Aug 02, 2009 9:16 pm
Location: Bayside, Melbourne, Victoria
Contact:

Re: VR with l67 help needed

Post by VX L67 Getrag »

It's a bin created to run the L67 on the VR computer hence $11P custom code.

It will run the early 4L60E without the TCC controlled by PWM or can also run the later 4L60E that has TCC with PWM control & the area to change those settings is in between $5219 & $548D need to be copied across to allow for it to work properly!
Attachments
OSE_$11P V103 CAKH V6 __ L67.BIN
(64 KiB) Downloaded 163 times
vp304
Posts: 451
Joined: Wed May 19, 2010 2:21 pm

Re: VR with l67 help needed

Post by vp304 »

So the bin you just posted is for a l67 engine in a vr running a vs 4l60e?
Any chance you can change the auto setting for me to suit my vr 4l60e . As it is beyond my skill level in tuner pro.
Thanks so much for this
VX L67 Getrag
Posts: 2877
Joined: Sun Aug 02, 2009 9:16 pm
Location: Bayside, Melbourne, Victoria
Contact:

Re: VR with l67 help needed

Post by VX L67 Getrag »

with info I was given this should do the trick!
Attachments
OSE_$11P V103 CAKH V6 __ L67 with non PWM TCC.BIN
(64 KiB) Downloaded 154 times
vp304
Posts: 451
Joined: Wed May 19, 2010 2:21 pm

Re: VR with l67 help needed

Post by vp304 »

vx l67 getrag thanks mate

About to buy a aldl cable of here to go with my old school moates ostrich.

Fired up your custom tune vx l67 getrag and looks like the timing maps are a bit scattered.
Ve fuel table i can sort out with my wideband no worries
But the timing boost table should i use this vt super 6 table below?
I mean the 450 onwards table part of vt super 6 map looks like its boost onwards as its pulling timing slowly. Should i drop this into my 11p boost part of map to get me going ?
See pics below
sorry about all the questions
Attachments
vt super 6 timing .jpg
forum l67 tune.jpg
User avatar
vlad01
Posts: 7780
Joined: Mon Oct 08, 2012 6:41 pm
cars: VP I S
VP I executive
VP II executive
VP II executive #2
VR II executive
Location: Kyneton, Vic

Re: VR with l67 help needed

Post by vlad01 »

That appears to be the stock vr spark table in the 2nd pic.
I'm the director of VSH (Vlad's Spec Holden), because HSV were doing it ass about.
VX L67 Getrag
Posts: 2877
Joined: Sun Aug 02, 2009 9:16 pm
Location: Bayside, Melbourne, Victoria
Contact:

Re: VR with l67 help needed

Post by VX L67 Getrag »

It's just a file that was created to get to a start point, so adjust fuel & timing as needed & it won't directly relate to the standard L67 files as there created for MAF & not MAP.
User avatar
delcowizzid
Posts: 5493
Joined: Sat Feb 28, 2009 8:38 pm
Location: Wellington NZ
Contact:

Re: VR with l67 help needed

Post by delcowizzid »

20 degrees everywhere on boost won't be nice haha
If Its Got Gas Or Ass Count Me In.if it cant be fixed with a hammer you have an electrical problem
Post Reply