TunerPro RT ? clearing codes?
- VL400
- Posts: 4991
- Joined: Sun Mar 01, 2009 2:54 pm
- cars: VL Calais and Toyota Landcruiser. Plus some toys :)
- Location: Perth, WA
- Contact:
Re: TunerPro RT ? clearing codes?
Looks like there is an error in the command, give the attached a go and let us know if it works so we can update the ADX thread.
- Attachments
-
- VS V6 Engine and Trans v1.10 WB 14.7kit.adx
- (145.18 KiB) Downloaded 313 times
-
- Posts: 8
- Joined: Fri May 10, 2013 5:15 pm
- cars: Toyota Hilux 86 w/VTII running on a VS comp + loom
Re: TunerPro RT ? clearing codes?
OK so heres how I went, downloaded new ADX and that work's now clears codes other one didn't
found I did indeed have a faulty TPS sensor so got a replacement one in. but to get it to set at 0% throttle I had to disconnect battery for 30 secs and then it came right so ive got 0.51V @ 0.00% TPS
Cheers for the help guys and keeping the code up to date... was doing my head in the whole thing with not resetting error codes id reinstalled tunerpro several times tried different laptops and re-installed drivers countless times also
Good to finally have it sorted though
Many thanks
Ash
found I did indeed have a faulty TPS sensor so got a replacement one in. but to get it to set at 0% throttle I had to disconnect battery for 30 secs and then it came right so ive got 0.51V @ 0.00% TPS
Cheers for the help guys and keeping the code up to date... was doing my head in the whole thing with not resetting error codes id reinstalled tunerpro several times tried different laptops and re-installed drivers countless times also
Good to finally have it sorted though
Many thanks
Ash
-
- Posts: 8
- Joined: Fri May 10, 2013 5:15 pm
- cars: Toyota Hilux 86 w/VTII running on a VS comp + loom
Re: TunerPro RT ? clearing codes?
OK so now ive just got 4 more DTC codes to get rid of im using an auto loom and computer in my conversion hooked up to a Toyota G52 manual transmission. I want to know if I can bypass these codes using resistors or something to fool computer into believing its still on an auto trans. so I don't have any codes thrown.
DTC 59:
TRANSMISSION FLUID TEMPERATURE (TFT) (SIGNAL VOLTAGE HIGH)
DTC 67:
TORQUE CONVERTER CLUTCH "ON-OFF" CIRCUIT FAULT
DTC 82:
1-2 SHIFT SOLENOID "A" CIRCUIT FAULT
DTC 83:
TORQUE CONVERTER CLUTCH (TCC) SOLENOID "PWM" CIRCUIT FAULT
Cheers Muchly
Ash
DTC 59:
TRANSMISSION FLUID TEMPERATURE (TFT) (SIGNAL VOLTAGE HIGH)
DTC 67:
TORQUE CONVERTER CLUTCH "ON-OFF" CIRCUIT FAULT
DTC 82:
1-2 SHIFT SOLENOID "A" CIRCUIT FAULT
DTC 83:
TORQUE CONVERTER CLUTCH (TCC) SOLENOID "PWM" CIRCUIT FAULT
Cheers Muchly
Ash
Last edited by Ashohman on Thu May 23, 2013 5:30 pm, edited 1 time in total.
- Holden202T
- Posts: 10311
- Joined: Sat Feb 28, 2009 9:05 pm
- Location: Tenambit, NSW
- Contact:
Re: TunerPro RT ? clearing codes?
i'd say you are going to need to disable the DTC's for those codes.
No matter what the question is, the answer is always more horsepower!
Just starting out? Have a read of the getting started guide
Basic tuning of a delco ECM with $12P thread
Advanced tuning of a delco ECM with $12P thread
Just starting out? Have a read of the getting started guide
Basic tuning of a delco ECM with $12P thread
Advanced tuning of a delco ECM with $12P thread