OSEPlugin for Tunerpro 5 v1.80
- antus
- Site Admin
- Posts: 8237
- Joined: Sat Feb 28, 2009 8:34 pm
- cars: TX Gemini 2L Twincam
TX Gemini SR20 18psi
Datsun 1200 Ute
Subaru Blitzen '06 EZ30 4th gen, 3.0R Spec B - Contact:
Re: OSEPlugin for Tunerpro 5 v1.49
Also confirm there is a jumper across the RW pin on the nvram.
Have you read the FAQ? For lots of information and links to significant threads see here: http://pcmhacking.net/forums/viewtopic.php?f=7&t=1396
-
- Posts: 20
- Joined: Thu Oct 17, 2013 2:24 pm
- cars: 1988 Pontiac Fiero GT
- Location: Thunder Bay Ontario, Canada
Re: OSEPlugin for Tunerpro 5 v1.49
Yup- done that too, but I guess pulling the board out to check it would be a good idea - I've checked and double checked everything else but not that.Jayme wrote:have you soldered in the write wire on the back of the pcm?
Thanks for the suggestion - any other possibilities?
Dave
Northstar powered 88 Fiero GT
88 Pontiac Fiero GT
-
- Posts: 20
- Joined: Thu Oct 17, 2013 2:24 pm
- cars: 1988 Pontiac Fiero GT
- Location: Thunder Bay Ontario, Canada
Re: OSEPlugin for Tunerpro 5 v1.49
OK - will do that at the same time I check the write wire.antus wrote:Also confirm there is a jumper across the RW pin on the nvram.
The write has worked on the initial installation, but I have since installed a dpdt switch for the A/B program and started using a new laptop. I was suspect of the laptop communication setup. Maybe the write wire is disturbed, or the RW jumper is off.
Thanks for your suggestions - I hope it's that simple....
Dave.
Northstar powered Fiero GT
88 Pontiac Fiero GT
- VL400
- Posts: 4991
- Joined: Sun Mar 01, 2009 2:54 pm
- cars: VL Calais and Toyota Landcruiser. Plus some toys :)
- Location: Perth, WA
- Contact:
Re: OSEPlugin for Tunerpro 5 v1.49
There was a recent post of a problem writing to an NVRAM which ended up being a bent pin where the NVRAM/MEMCAL plugs in so worth checking that also. I have defined an item in the 12P ADX to show if the NVRAM is read-only or writable which may help your fault finding. http://pcmhacking.net/forums/viewtopic. ... ire#p41699
-
- Posts: 20
- Joined: Thu Oct 17, 2013 2:24 pm
- cars: 1988 Pontiac Fiero GT
- Location: Thunder Bay Ontario, Canada
Re: OSEPlugin for Tunerpro 5 v1.49
Success!
The RW jumper was on correctly and so was the write-enable jumper wire. Removed and replaced the RW jumper and all seems to work now. I still don't understand what the hangup was but I'll take it.
Thanks for your help guys!
Dave.
The RW jumper was on correctly and so was the write-enable jumper wire. Removed and replaced the RW jumper and all seems to work now. I still don't understand what the hangup was but I'll take it.
Thanks for your help guys!
Dave.
88 Pontiac Fiero GT
- delcowizzid
- Posts: 5493
- Joined: Sat Feb 28, 2009 8:38 pm
- Location: Wellington NZ
- Contact:
Re: OSEPlugin for Tunerpro 5 v1.49
post up a ride thread in members rides so we can see what you have $12p running in
If Its Got Gas Or Ass Count Me In.if it cant be fixed with a hammer you have an electrical problem
Re: OSEPlugin for Tunerpro 5 v1.49
Hey guys got a issue
I am Using TP5 8383 with OSEplugin 1.49 and i can not get it to connect to my vp v8 nvram ecm i got it back in the mail today from VL400 and worked when he tested it .
my Flashtool v145 works so i am unsure what i am doing wrong
I am Using TP5 8383 with OSEplugin 1.49 and i can not get it to connect to my vp v8 nvram ecm i got it back in the mail today from VL400 and worked when he tested it .
my Flashtool v145 works so i am unsure what i am doing wrong
- VL400
- Posts: 4991
- Joined: Sun Mar 01, 2009 2:54 pm
- cars: VL Calais and Toyota Landcruiser. Plus some toys :)
- Location: Perth, WA
- Contact:
Re: OSEPlugin for Tunerpro 5 v1.49
Have you setup the plugin preferences as per the first post in this thread? http://pcmhacking.net/forums/viewtopic.php?f=3&t=590
That should allow the ECU to be detected using the initialize emulation hardware button.
To connect and log you need the 12P ADX loaded .. http://pcmhacking.net/forums/viewtopic.php?f=27&t=356
The NVRAM is loaded with standard 12P V111 V8 bins on both banks.
That should allow the ECU to be detected using the initialize emulation hardware button.
To connect and log you need the 12P ADX loaded .. http://pcmhacking.net/forums/viewtopic.php?f=27&t=356
The NVRAM is loaded with standard 12P V111 V8 bins on both banks.
Re: OSEPlugin for Tunerpro 5 v1.49
VL400 everything you have stated i have done this time and last time but also i tried it again later on and the engine fan would come one a soon as the ignition was on to acc so now i do not know wtf is going on might pull the board out of the socket and check pins i hope its not damaged again .
if it is damaged then auspost have stuffed it as the case was slightly bent
if it is damaged then auspost have stuffed it as the case was slightly bent
- antus
- Site Admin
- Posts: 8237
- Joined: Sat Feb 28, 2009 8:34 pm
- cars: TX Gemini 2L Twincam
TX Gemini SR20 18psi
Datsun 1200 Ute
Subaru Blitzen '06 EZ30 4th gen, 3.0R Spec B - Contact:
Re: OSEPlugin for Tunerpro 5 v1.50
Version 1.50 has been released. The main change is that verification has been implemented. Click the red circled button to compare the bin loaded in TunerPro with the NVRAM contents. You will either get an OK, or a fail with some debug info.
Keep in mind that some 12P functionality such as knock logging or VE learn can trigger verification failures when there is not a problem. Success you can be sure of.
Keep in mind that some 12P functionality such as knock logging or VE learn can trigger verification failures when there is not a problem. Success you can be sure of.
Have you read the FAQ? For lots of information and links to significant threads see here: http://pcmhacking.net/forums/viewtopic.php?f=7&t=1396